background image

Before You Begin

DEAR ECHO Bear Cat

®

 CUSTOMER

Thank you for purchasing an ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufactured 

to give years of dependable performance. To keep your machine operating at peak efficiency, it is necessary to adjust 

it correctly and make regular inspections. The following pages will assist you in the operation and maintenance of your 

machine. Please read and understand this manual before operating your machine.
If you have any questions or comments about this manual, please call us toll-free at 888.625.4520.
If you have any questions or problems with your machine, please call or write your local authorized ECHO Bear Cat 

dealer.
This document is based on information available at the time of its publication. ECHO Bear Cat is continually making 

improvements and developing new equipment. In doing so, we reserve the right to make changes or add improvements 

to our product without obligation for equipment previously sold.

PLEASE SEND US YOUR WARRANTY CARD

A warranty card is included in your owner’s kit packaged with your machine. Please take the time to fill in the information 

requested on the card. When you send your completed card to us, we will register your machine and start your coverage 

under our limited warranty or go to bearcatproducts.com/Product-Support/Product-Registration.

SERIAL NUMBER OR VIN

© 2017, CRARY

®

 INDUSTRIES, ALL RIGHTS RESERVED. PRODUCED AND PRINTED IN THE U.S.A.

IDENTIFICATION NUMBER LOCATION

Your machine will have either a serial number or vehicle 

identification number (VIN). VINs are located on the left 

side of the trailer frame near the hitch. They are 17-digit 

numbers of the format: 5VJAA001XXWXXXXXX. Serial 

numbers are located on the machine body. They are 

6-digit numbers.

Record your identification number in the space provided 

and on the warranty registration card. 

FOR MACHINE SERVICE OR PARTS

For service assistance, contact your nearest authorized 

ECHO Bear Cat dealer or the factory. For parts, contact 

your authorized dealer. The parts manual for your 

machine is available at bearcatproducts.com/Product-

Support/Find-A-Product-Manual. Your dealer will need to 

know the identification number of your machine to provide 

the most efficient service. See below for information on 

how  to  identify  and  record  the  identification  number  for 

your machine.

FOR ENGINE SERVICE OR PARTS

For engine service or parts, contact your nearest 

authorized engine dealer. ECHO Bear Cat does not 

handle any parts, repairs or warranties for engines.

ORDERING PARTS

Only genuine ECHO Bear Cat replacement parts should 

be used to repair the machine. Replacement parts 

manufactured by others could present safety hazards, 

even though they may fit on this machine. Replacement 

parts are available from your ECHO Bear Cat dealer.

Provide the following when ordering parts:

The SERIAL NUMBER or VIN of your machine.
The PART NUMBER of the part.
The PART DESCRIPTION.
The QUANTITY needed.

HOW TO CONTACT ECHO Bear Cat

ADDRESS

PHONE

E-MAIL

HOURS

237 NW 12th Street 

P.O. Box 849 

West Fargo, ND 58078

888.625.4520 

701.282.5520 

Fax: 701.282.9522

[email protected] 

[email protected]

Monday - Friday 

8 a.m. to 5 p.m. 

Central Time

Содержание CH8540




























Отзывы: