background image

FRESH WATER FLUSH PROCEDURE 

 

Caution:    The  fresh  water  pressure  should  not  exceed  the  range  of  the  low  pressure  gauge/s.  
The installation of a pressure reducer may be necessary. 

 
You should fresh water flush your watermaker after every use or infuse a biocide solution for long 
term storage.  The fresh water flush prepares your watermaker for a shut down period of seven days 
maximum.  You can repeat the flush procedure every seven days, to extend the short term storage. 
 
1) 

Open the pressure control-valve all the way counter-clockwise.

   

2) 

Close  the  seawater  intake-valve  on  the  pre-filter  assembly  and  make  sure  the  shut  off 
valve on the flush filter is open. 

3) 

Open  the  fresh  water  flush  valve  on  the  pre-filter  assembly.  Your  fresh  water  pressure 
pump should now turn on.  Allow fresh water to flow until all salt water is flushed out of 
the system. 
For the next flush procedure, test how long it takes until the brine at the reject outlet of 
the watermaker becomes fresh. 

 

4) 

Close the fresh water flush valve and the seawater shut off valve. 

 

MEMBRANE STORAGE PROCEDURE 

 
If  you  intend  to  store  your  watermaker  for  more  than  ten  days,  growth  of  microorganism  will 
degrade the RO membranes performance.   
 
The  RO  membranes  should  be  flushed  with  a  biocide solution to preserve the membrane for long-
term storage of up to ten months.

 

 

1) 

Fresh water flush the system. 

 
2) 

In  a  clean  plastic  container,  mix  5  gallons  /  20  litres  of  un-chlorinated fresh water with 
200 grams (2/3 container) of Echo Tec. Preservative # 3.   
 

3) 

Switch  the  three-way  valve  to  the  service  position.    Switch  the  diverter  valve  to  the 
sample position.  Switch the shut off valve to the off position. 

 
4) 

Open  the  pressure  control  valve  all  the  way  anti-clockwise  and  start  the  high  pressure 
pump only by holding down the start-button in the selector switch “Off” position. 

 
5) 

Infuse  the  solution  via  the  service  hose  connected  to  the  three-way valve while running 
the high-pressure pump without pressure.  When the solution has been infused, switch the 
watermaker off and remove the pre-filter cartridges for dry storage. 

 
Under best conditions your watermaker is now prepared for a shut down period of ten months. 
 
Discard  the  product  water  for  at  least  thirty  minutes  of  initial  operation,  after  storage,  before 
drinking or before use in food preparations.

 

Содержание BEACH HOUSE Series


















Отзывы: