background image

920-0002-00 Rev. B

Page 3 of 8

 

 CAUTION!

Disable power before wiring up the beacon/strobe 

head, to prevent accidental shorting, arcing, and 

electrical shock.

Important! 

 This system must be connected to a

separate, fused power point.  Do not wire in parallel 

with any other accessory.

Gerneral Wiring Instructions:

1. Route 14AWG or larger wires from the vehicle positive (battery, 

    alternator, fuse block) to the switch panel in the cab.  Use high-

    temperature wire if it passes through the engine compartment.  

    Install an inline fuse close to the power take-off point.  For each 

    circuit, use a fuse according to the following tables:  

2. Connect the power wires to the positive side of the appropriate 

    lightbar switch or switches of the switch panel with quick

    disconnect terminals or by soldering.

3. After the light bar has been mounted, route the lightbar cable 

    into the vehicle to the switch panel location

4. Connect the 16 AWG wires (14 AWG on the 2-Con 

    Ground System) of the lightbar cable to the switched side of 

    each switch.  See the tables below for wire color / function 

    legend. Your bar may not be equipped with all of these functions; 

    unused wires may be trimmed flush with cable end.

5. Connect the lightbar cable ground wire to a solid ground 

    connection on the vehicle.  If this wire needs to be lengthened, 

    use a 10AWG or larger White wire.

6. Use cable ties to secure all cables and wires.

2 CON GROUND CABLE SYSTEM

CIRCUIT

WIRE COLOR

FUSE VALUE (12V SYSTEM)

OUTER ROTATORS (2 OUTERMOST)

RED

15 AMP

INNER ROTATORS  (ALL OTHER)

BLUE

20 AMP

GROUND

BLACK

N/A

12 CON GROUND CABLE SYSTEM

CIRCUIT

WIRE COLOR

FUSE VALUE (12V SYSTEM)

OUTER ROTATORS (2 OUTERMOST)

RED

15 AMP

INNER ROTATORS   (ALL OTHERS)

BLUE

15 AMP

STOP / TAIL / TURN

 (DOT)**

PASSENGER SIDE STOP / TURN

VIOLET

VEHICLE FUSE

STOP / TAIL / TURN (DOT)

I.D. (DOT)/TAIL

BROWN

VEHICLE FUSE

STOP / TAIL / TURN (DOT)

DRIVER SIDE STOP / TURN

YELLOW

VEHICLE FUSE

REAR FACING WORK LIGHTS

GRAY

15 AMP

ALTERNATING FLASHER – FRONT

BLACK

10 AMP

ALTERNATING FLASHER – REAR

WHITE W/RED STRIPE

10 AMP

STROBE SYSTEM POWER

WHITE W/BLACK STRIPE

10 AMP (2 STROBES)

15 AMP (4 STROBES)

STROBE SYSTEM DUAL / QUAD FLASH 

CONTROL

ORANGE (GROUNDED FOR QUAD 

MODE)*

NO FUSE REQ’D

STROBE SYSTEM DAY / NIGHT FLASH 

CONTROL

GREEN (GROUNDED FOR NIGHT 

MODE)*

NO FUSE REQ’D

NOT USED

WHITE W/BROWN STRIPE

N/A

GROUND

WHITE

N/A

* To switch between dual/quad mode or day/night mode, connect these wires to a switch. Connect the other side of the switch to 

   ground.
** Department of Transportation System

Содержание Evolution Series









Отзывы: