manualshive.com logo in svg

Ecco 27 Series, Инструкции по сборке, установке и эксплуатации, Страница: 3 / 17

Поделиться
Скачать
Ecco 27 Series Скачать руководство пользователя страница 3

Page 3 of 18

FIGURE 2

FIGURE 1

OVERSIZED FLAT WASHER

1/4” NYLON INSERT NUT

ADJUSTABLE FOOT

COVER

RUBBER PAD

1/4” - 20 HEX BOLT

VEHICLE

ROOF

FLAT ROOF

CURVED ROOF

WEDGE RUBBER PAD

FLAT RUBBER PAD

Permanent Mounting with Adjustable Mounting Feet

1. Loosen the 5/16” nuts to allow the mounting feet to slide along the base. Place the lightbar over the center of the vehicle and slide the

mounting feet into position near the curved edges of the roof when possible.

2. Secure the feet in location on the lightbar by tightening the four nuts on each foot.

3. With the feet positioned, remove the adjustable foot cover and mark the location of the mounting hole centers on the roof of the vehicle.

Remove the lightbar and drill the mounting holes as marked. Note: The center distance between the mounting holes in an adjustable

mounting foot is 11.1” or 281.94 mm.

4. Attach the appropriate foot pad for the curvature of the roof surface per FIGURE 2. Secure the lightbar feet to the vehicle using the

supplied 1/4”-20 hardware and reattach the adjustable foot cover as shown in FIGURE 1. See the Wiring section of this manual for

further wiring instructions.

Содержание 27 Series


















Отзывы:

Нет отзывов