manualshive.com logo in svg

Ecco 27 Series, Инструкции по сборке, установке и эксплуатации, Страница: 15 / 17

Поделиться
Скачать
Ecco 27 Series Скачать руководство пользователя страница 15

Page 15 of 18

FIGURE 8

CORNER MODULE

LED TD/ALLEY

MODULE

DIRECTIONAL

MODULE

FIGURE 9

Twist to

 lift lens

Pry up

to remove

lens clip

Options and Maintenance:

Lens Cleaning

Occasional cleaning of the lenses will ensure optimum light output. Take care when cleaning lenses  - although tough, polycarbonate 

scratches easily. Clean the lens and base with soap and water or a lens polish using a soft cloth. Do not use solvents as they may damage 

the polycarbonate.

Lens Removal and Installation

1. Uninstall the lens clips (4 per lens), as shown in FIGURE 8, using a flat blade screwdriver.

2. Insert the screwdriver into the gap along the lens edge, and twist the screwdriver to lift the lens.

3. When finished, reinstall making sure the lens gasket is not damaged or folded. Replace the clips by hooking into the bottom lens slot and

pressing the upper portion into the clip pocket.

LED Module Removal and/or Replacement

1. Remove screw(s) securing the light head assembly to the lower lens as shown in FIGURE 9.

2. Lift the light head assembly and disconnect the wiring at the connectors.

3. During re-assembly, repeat the prior steps in reverse order. Torque screw(s) to 10 in-lbs or 1.13 Nm.

Содержание 27 Series


















Отзывы:

Нет отзывов