manualshive.com logo in svg

ECCO STOVE 730EC2, Руководство пользователя

Поделиться
Скачать
ECCO STOVE 730EC2 Скачать руководство пользователя страница 20

 

730/03.05.23/V2 

 

P a g e |

20

 

of 29

 

Ecco Stove | Foster House | 2 Redditch Road | Studley | B80 7AX | United Kingdom 

T

 | +44 (0) 1527 857 814           

E

 | 

[email protected]

           

W

 | www.eccostove.com 

For all patents 

–

 See Addendum 

j)

 

Co-concentration at 0.07 @ 13%O

2.  

Excessive flue draught may remove too much heat from the 

Ecco Stove on slow combustion.  A damper may be fitted into the flue pipe off the stove to 
reduce draught but only closed after the firing process is completed 

–

 dampers must always 

allow 20% of the flue area unclosed. 

 
 
24. DUCTED WARM AIR (WHEN AVAILABLE) 

 

By fitting the hot box with one extra trim between it and the stoves top, up to 
 four 100mm diameter rigid pipes can be fitted off the stoves top to other rooms.   
These pipes simply push into the openings in the top of the hot box. 

 

Grilles with spigots are available separately along with rigid 100mm pipes and 
 100mm alloy flexible tubing (none of which are included as standard).  Maximum  
duct length per output is 1.5 metres.  Each duct must rise constantly to its point 
 of emission into the adjacent room (or the same room the Ecco Stove stands in) 
 

with a minimum angle of 45⁰ for na

tural convection. 

 

The rigid pipes are used as decorative outlets rather than flexible tubing visible  
directly off the top of the hot box.  A steel  locating plate which clamps onto the  
flue pipe is available to hold the rigid duct pipes in position for appearances only. 
 

25. GENERAL 

 

a)

 

Safe Operation.  The outside surface of the Ecco Stove will reach temperatures above 200

˚C

  on 

full firing and must not be touched as burning will occur.  

Care must be taken.

 

In the event of overheating 

–

 above 230

˚

C ensure the fire door and ash pit door are fully closed 

in order to reduce the rate of combustion and slowly cool the stove.  
a i)  Any combustible materials must be a minimum of  500mm away from the appliance sides.  
Plaster board or plaster will crack if within 300 mm of the appliance.  Non combustible materials 
must be minimum of 125mm from sides; 300mm above and 75mm from rear. 

b)

 

No modifications must be made to Ecco Stove or structural work carried out upon it unless by 
authorised personnel (aesthetic changes may be made by the manufacturer without notice). 

c)

 

Replacement parts must only be of the manufacturers supply and design. 
The following parts are packed with the Ecco Stove. 
1 x Bottom section (silicon carbide), Ashcan; 2 x alloy cleaning pugs; 
1 x grate section (silicon carbide) 1 x cast iron fixed grate 
2 x side sections (silicon carbide)  
1 x back section (silicon carbide) 1 x vermiculite back baffle with predrilled holes; 2 x vermiculite 
spacer blocks.  
1 x steel baffle complete assembly with vermiculite board and 2 wedges 
1 x door and frame including glass pre-fitted (cast iron) 
1 x air spinner in cast iron with pre-fitted threaded rod affixed 
1 x baffle brick (silicon carbide) top section 
4 x cleaning plugs in alloy or cast iron 
1 x flue cleaning brush 
1 x stove thermometer 

ducts off 

Содержание 730EC2



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды