EC-PACK EC-JET 2000 Скачать руководство пользователя страница 33

Страница: 33 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

5.3.8.

Number of Buffer

Sets the number of data bars that the remote buffer can cache

5.3.9.

Clear Buffer

It can choose to whether clear the remote buffer or not when the printing stops.

5.4.

Consumable

Management Mode:

Three kinds of management mode:

◆

Factory mode

Use in the factory during testing.

◆

Factory fresh mode

It changes to factory fresh mode when the factory finishes testing and checking. It can

only print 7 dots raster data in this mode.

◆

Bound Mode

Change to bound mode when input the distributor PIN in the factory mode. In this mode,

new CSN quality mode will be reminded to verify and add new consumable when the

time of consumable of ink and solvent is empty.

Distributor PIN

A length of four characters related to distributor PIN will be shown under bound mode.

Solvent remaining time

Show the time of current solvent CSN can be used.

Ink remaining time

Show the time of current ink CSN can be used. This time is calculated by the number of printing
ink drops. This value will be meaningless if it doesn’t in the status of printing and the printing

time is less than 1 minute.

Adding time of solvent

Show the automatic adding time of solvent from starting the printer. This count value will be

cleared after restart.

Type of ink

Set the type of using ink.

Содержание EC-JET 2000












































































































Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды

EC-PACK EC-JET 2000, Руководство пользователя

Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды