EC-PACK EC-JET 2000 Скачать руководство пользователя страница 24

Страница: 24 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

3.11.1.

Status line from the top

Show the jetting status of the printer.

◆

Jet off -- The jet has been stopped.

◆

Jet running -- The jet is running but printing is stopped.

◆

Printing -- The jet is running and the printer is ready to print.

3.11.2.

Solvent

Show status of solvent level check.

◆

OK - Solvent level is acceptable.

◆

LOW - Add one bottle of solvent.

3.11.3.

Ink

Show status of ink level check.

◆

OK - Ink level is acceptable.

◆

LOW - Add one bottle of ink.

The ink and solvent levels should show OK. If not, they must be refilled with the correct ink or

solvent.

3.11.4.

Current warning message

Current warning messages of the printer are listed in the warning message list.

Содержание EC-JET 2000












































































































Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды

EC-PACK EC-JET 2000, Руководство пользователя

Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды