EC-PACK EC-JET 2000 Скачать руководство пользователя страница 31

Страница: 31 / 107

User Manual The1.1 version of 2018 Guangzhou EC-PACK CO.LTD

Alarm output interface divides into two parts, above and under section. Three buttons above

represent the output of the three ways. Pressing the button can switch the different alarm output

way.

The following lists represent different alarm items. Press the menu from output port drop-down

menu to select this alarm output port or select no alarm output.

5.3.

Remote Communication

EC2000 printer support RS-232 and LAN TCP this two ways to remote communication. See
“EC-JET Communication Protocol V3.1” for specific communication format. Setup interface of

remote communication is below:

5.3.1.

Network Listening Port

Network listening port is used to set the connection of TCP. TCP communication needs to set the

IP address of printer and the IP address of communication host to a same LAN, and need to use

the specified listening port to access.

5.3.2.

Baud Rate

Baud Rate is used to set the communication rate during using RS-232 communication.

5.3.3.

Communication Address

Содержание EC-JET 2000












































































































Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды

EC-PACK EC-JET 2000, Руководство пользователя

Результаты поиска

Содержание EC-JET 2000

Отзывы:

Бренды по названию

Популярные бренды