background image

SX1278 Wireless Module

E32 Series User Manual

Copyright ©2012–2017, Chengdu Ebyte Electronic Technology Co., Ltd.

21

/

24

------------------------------------------------------

5,4,3

wireless wake-up time(for the receiver,

it means the monitor interval time ,while for the

transmitter it means continuously sending

preamble code time.)

000:250ms(default)

001:500ms

010:750ms

011:1000ms

100:1250ms

101:1500ms

110:1750ms

111:2000ms

----------------------------------------------------

2,

FEC switch

0:Turn off FEC

1:Turn on FEC(Default)

------------------------------------------------------

1, 0

transmission power (approximation)

00: 30dBm(Default)

01: 27dBm

10: 24dBm

11: 21dBm

------------------------------------------------------------

The transmit & receive module work in mode 0,

whose delay time is invalid & can be arbitrary

value.

The transmitter works in mode 1 can transmit the

preamble code of the corresponding time

continuously.

When the receiver works in mode 2, the time

means the monitor interval time (wireless

wake-up). Only the data from transmitter that

works in mode 1 can be received.

The wake-up time set by transmitter cannot be less

than the monitor interval time of receiver;

otherwise, it may lead to data loss. In case of

two-way communication, both parties should keep

the wake-up time the same.

The longer the wake-up time, the lower the

average receive current consumption.

-------------------------------------------------------------

After turn off FEC, the actual data transmission rate

increases while anti-interference ability decreases.

Also the transmission distance is relatively short.

Both communication parties must keep on the

same pages about turn-on or turn-off FEC.

-------------------------------------------------------------

The external power must make sure the ability of

current output more than 1.5A and ensure the

power supply ripple within 100mV.

Low power transmission is not recommended due

to its low power supply efficiency.

For example: The meaning of No.3 "SPED" byte

The binary bit of the byte

7

6

5

4

3

2

1

0

Configures by user

0

0

0

1

1

0

1

0

Meaning

UART parity bit 8N1

UART baud rate is 9600

Air data rate is 2.4k

Corresponding hexadecimal

1

A

Содержание E32 Series

























Отзывы: