EBS LX20G Скачать руководство пользователя страница 10

Страница: 10 / 69

LX20G_Manual_en_v2.1

Page 10 /

Terminal

Connection description

GND

Ground of the device, common terminal for inputs and

outputs.

+12V

Positive supply terminal 12-14V DC.

PWR

Input for monitoring the presence of AC power. It works only
with dedicated power supply LX-ZAS.

BTT

Input for monitoring the presence of battery attached to the

power supply unit. It works only with dedicated power supply
LX-ZAS.

IN1, IN2

Inputs allow the connection of additional detectors or control

panel outputs (eg. testing of outputs).

TMP

Sabotage switch.

OUT1, OUT2

OUT3

OC type outputs. It may control external devices or for
connecting to the control panel zones (eg. as feedback during

the testing of the system). Provides ground during activation.

RING - TIP

Terminals for an PSTN telephone line

T1 – R1

To the phone communicator of control panel.

T2 – R2

For connecting a telephone (eg. during transmission test.

NOTES:

It is recommended that connecting cables to these terminals were not

longer that 3m.

OUT1, OUT2, OUT3 outputs can load up to 100mA. Don’t short this output
to power supply because it can cause permanent damage of output.

Don’t connect power supply when GSM antenna isn’t connected, because it
can cause permanent damage of GSM/GPRS modem.

After careful connections examination a battery may be connected (to +AKU

and GND terminals) and then power may be switched on for transformer and
programming procedure of transmitter may begin (See chapter 6).

3.2.

PCB VERSION

THE FOLLOWING CONNECTIONS ARE PURPOSED FOR COOPERATION WITH LX-
ZAS POWER SUPPLY. IF OTHER POWER SUPPLY APPLIED, INPUTS SHALL BE LEFT
WITHOUT WIRING.

Содержание LX20G






































































Результаты поиска

Содержание LX20G

Отзывы:

Похожие инструкции для LX20G

Бренды по названию

Популярные бренды

EBS LX20G, Инструкция по установке и программированию

Результаты поиска

Содержание LX20G

Отзывы:

Похожие инструкции для LX20G

Бренды по названию

Популярные бренды