Operating instructions
K3GA00-PV03-01
Translation of the original operating instructions
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 61800-5-1; CE
Approval
UL 1004-7 + 60730; CSA C22.2 No. 77
+ CAN/CSA-E60730-1; EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.5 Mounting data
Strength class of
screws
10.9
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
3.6 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
+80 °C
Min. permitted
ambient temp. for
motor (transport/
storage)
-40 °C
3.7 Electromagnetic compatibility
EMC immunity to
interference
According to EN 61000-6-2 (industrial
environment)
EMC interference
emission
According to EN 61000-6-4 (industrial
environment)
4. CONNECTION AND STARTUP
4.1 Mechanical connection
DANGER
Heavy and unwieldy device.
Crushing hazard
→ Do not grasp or transport the device by the fan impeller.
Move the device with a crane using ropes or cloth straps.
There are holes drilled in the support structure that can be
used for transport.
→ After installation, ensure that the blades on the fan
impeller are not deformed or bent.
CAUTION
Risk of cutting and crushing when removing device
from packaging
→ Carefully remove the device from the packaging by grasping
hold of the frame. Never subject to any impact.
→ Wear safety shoes and cut-resistant safety gloves.
CAUTION
Device weighs over 25 kg! Heavy load when unpacking
device.
Risk of physical injury, such as back injuries.
→ Use suitable hoisting equipment to remove the device from
its packaging.
NOTE
Damage to the device from vibration
Bearing damage, shorter service life
→ The fan must not be subjected to force or excessive vibration
from sections of the installation. #It is advisable to use spring
or rubber isolators for decoupling (not included in scope of
delivery). The fan is to be operated sufficiently far away from
the resonant frequency of the vibration isolators. #If the fan is
connected to air ducts, the connection should be isolated
from vibration, e.g. using compensators or similar elements.
→ Ensure stress-free attachment of the fan to the sub-structure.
;
The fan may not be handled in the area around the inlet nozzle during
transport and installation.
There is a risk of damage to the impeller.
;
Check the device for transport damage. Damaged devices are not to
be installed.
;
Install the undamaged device in accordance with your application.
4.1.1 Installation of RadiPac fan
During installation, transport the RadiPac only with suitable hoisting and
supporting equipment. Use only suitable ropes or chains (see Chapter
3.4 Technical description for product weight). Note that the angle
between the ropes or chains may be between 0° and 60°. To attach the
hoisting equipment, use four M10 eye bolts that can turn under load;
screw the eye bolts into the available threaded holes. Do not use
standard DIN 580 eye bolts. The maximum acceleration during transport
may not exceed 2 g.
Item no. 55793-5-9970 · ENU · Change 94781 · Approved 2018-01-23 · Page 6 / 15
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com
