ebm-papst K3GA00-PV03-01 Скачать руководство пользователя

Страница: 4 / 15

Operating instructions

K3GA00-PV03-01

Translation of the original operating instructions

3. TECHNICAL DATA

3.1 Product drawing

All dimensions in mm.

Inlet ring with pressure tap (k-factor: 1200)

Mounting position for vibration-absorbing elements, tightening torque max. 40 Nm

Cable diameter min. 5 mm, max. 13 mm, tightening torque 4 ± 0.6 Nm

Cable diameter min. 16 mm, max. 20.5 mm, tightening torque 6 ± 0.9 Nm

Tightening torque 3.5 ± 0.5 Nm

Mounting holes for FlowGrid

Installation position: shaft horizontal (motor support plate must stand upright) or rotor on bottom; rotor on top on request

Item no. 55793-5-9970 · ENU · Change 94781 · Approved 2018-01-23 · Page 4 / 15

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

Содержание K3GA00-PV03-01
















Результаты поиска

Содержание K3GA00-PV03-01

Отзывы:

Похожие инструкции для K3GA00-PV03-01

Бренды по названию

Популярные бренды

ebm-papst K3GA00-PV03-01, Руководство по эксплуатации

Результаты поиска

Содержание K3GA00-PV03-01

Отзывы:

Похожие инструкции для K3GA00-PV03-01

Бренды по названию

Популярные бренды