Eaton VORAD AlwaysAlert Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 30

background image

4

Component Installation

Antenna Assembly

Installation

Antenna Assembly Installation

There are three antenna assembly mounting options to choose from (two surface and one recessed). To determine
which will work best, review the options and note that there are seven installation holes and one cable pass-through
hole required. These locations are easily established using the license plate mounting plate as a template.

The antenna assembly must be mounted on the centerline of the vehicle generally between sixteen (16) and forty-eight
(48) inches from the ground.

Note: These are general guidelines for the antenna mounting height, however, height recommendations vary based on

vehicle type, application, and cosmetic design characteristics.

«
...
5
6
7
8
9
...
»

Содержание VORAD AlwaysAlert































Отзывы:

Нет отзывов

Похожие инструкции для VORAD AlwaysAlert

Бренд: Data Aire Страницы: 82

Бренд: Echo Страницы: 4

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: Monacor Страницы: 2

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 8

Бренд: UNIT 1 Страницы: 23

Бренд: Kabuto Страницы: 16

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 32

Бренд: R-Go Страницы: 2

Бренд: R&S Страницы: 52

Бренд: Pout Страницы: 5

Бренд: Subaru Страницы: 3

Бренд: hepco & becker Страницы: 4

Easyrack 6622520 01 01

Бренд: hepco & becker Страницы: 4

Бренд: UPPAbaby Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды