background image

3

Instructional Booklet 

IB022010EN

Effective July 2019

Revision #4

Instructions for installation, operation,  

and maintenance of medium voltage 

VC-W MR2 (integral racking) 

EATON

 www.eaton.com

Disclaimer of warranties and limitation of liability

This instruction booklet is published solely for information purposes 

and should not be considered all-inclusive . If further information is 

required, you should consult an authorized Eaton sales representative .
The sale of the product shown in this literature is subject to the 

terms and conditions outlined in appropriate Eaton selling policies 

or other contractual agreement between the parties . This literature 

is not intended to and does not enlarge or add to any such contract . 

The sole source governing the rights and remedies of any purchaser 

of this equipment is the contract between the purchaser and Eaton .

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING 

WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE 

OR MERCHANTABILITY, OR WARRANTIES ARISING FROM 

THE COURSE OF DEALING OR USAGE OF TRADE, ARE MADE 

REGARDING THE INFORMATION, RECOMMENDATIONS, AND 

DESCRIPTIONS CONTAINED HEREIN.

 

In no event will Eaton be responsible to the purchaser or user in 

contract, in tort (including negligence), strict liability or otherwise 

for any special, indirect,incidental or consequential damage or loss 

whatsoever, including but not limited to damage or loss of use of 

equipment, plant or power system, cost of capital, loss of power, 

additional expenses in the use of existing power facilities, or claims 

against the purchaser or user by its customers resulting from the 

use of the information, recommendations and description contained 

herein .

Содержание VC-W MR2



















Отзывы: