Eaton PM3 Скачать руководство пользователя страница 9

Страница: 9 / 20

Instruction Leaflet

IL012002EN

Effective March 2013

Instruction Leaflet for Modbus Power Monitoring/

Metering Module (PM3) for FD, JG, and KD/LG

Circuit Breakers and Motor Circuit Protectors

EATON CORPORATION

www.eaton.com

2. Indicators

Figure 11. Status Indicators (KD/LG PM3).

2.1. Status Indicator

A single green LED is used to indicate the status of the

Measurement Board. The indicator has three states:

1. OFF

No light emission indicates internal DC power is not available, or the

Measurement Board has malfunctioned.

2. ON

Continuous light emission indicates power is applied, but the

Measurement Board is executing a power-on self test.

3. Slow Flash

Repetitive one second on, one second off indicates the

Measurement Board is operating normally.

Fast Flash

0.5 second on, 0.5 second off indicates one of three failures:

•

Unit not calibrated;

•

Unit has not been assembled properly; or

•

Unit memory has been damaged.

Status

RX Led

TX Led

Com

DC Common

+24

VDC

Earth

Ground

Settings

Network Address

Neutral

Red Bell Alarm

Common

Blue Aux Alarm

No Connect

2.2. Modbus Status Indicator

Modbus Rx Indicator

When illuminated, this green LED indicates the Communications

Board is receiving messages on the Modbus network.

ote:

This LED will typically be a solid green. That is, it will not flash as the

transmit LED does.

Modbus Tx Indicator

When illuminated, this green LED indicates the Communications

Board is transmitting a message on the Modbus network.

ote:

This LED typically flashes as the Communications Board transmits

messages over the Modbus network.

Содержание PM3





















Результаты поиска

Содержание PM3

Отзывы:

Похожие инструкции для PM3

Бренды по названию

Популярные бренды

Eaton PM3, Инструкция

Результаты поиска

Содержание PM3

Отзывы:

Похожие инструкции для PM3

Бренды по названию

Популярные бренды