manualshive.com logo in svg

Eaton OPTC4 LonWorks, Руководство пользователя

Поделиться
Скачать
Eaton OPTC4 LonWorks Скачать руководство пользователя страница 35

LonWorks Option Board User Manual

MN04003008E

For more information visit: 

www.eatonelectrical.com

6-9

April 2004

nciNmlSpeed

This configuration property is used to provide the nominal speed of the motor in RPM. This 
value is necessary to determine the minimum and maximum speeds for the motor, based on 
the configuration properties nciMinSpeed, nciMaxSpeed (entered as a percentage of nominal 
speed).

nciNmlFreq

This configuration property is used to provide the nominal frequency for the motor.

nciRampUpTm 

Defines the acceleration time for the 9000X drive. The valid range is 0.0 to 6,553.4 sec 
(0.1 sec).

nciRampDownTm

Defines the deceleration time for the 9000X drive. The valid range is 0.0 to 6,553.4 sec 
(0.1 sec).

nciDrvSpeedScale

This configuration property is used as the default value for nviDrvSpeedScale. This value will 
be adopted at power-up and in case no input variable within the specified Receive Heartbeat 
time is received. 

Содержание OPTC4 LonWorks













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды