manualshive.com logo in svg
background image

Instruction Booklet

Page

 24

Effective:  July 2010

2-Position Contactor Based 

Non-Automatic Transfer Switch

© 2010 Eaton Corporation

All Rights Reserved

Printed in USA

Publication No. IB01602046E/TBG00320

July 2010

This instruction booklet is published solely for information pur-

poses and should not be considered all-inclusive.  If further infor-

mation is required, you should consult Eaton.

Sale of the product(s) shown in this literature is subject to terms 

and conditions outlined in appropriate Eaton selling policies or 

other contractual agreements between the parties.  This literature 

is not intended to and does not enlarge or add to any such con-

tract.  The sole source governing the rights and remedies of any 

purchaser of this equipment is the contract between the pur-

chaser and Eaton.

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WAR-

RANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MER-

CHANTABILITY, OR WARRANTIES ARISING FROM COURSE OF 

DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE 

INFORMATION, RECOMMENDATIONS AND DESCRIPTIONS 

CONTAINED HEREIN.  In no event will Eaton be responsible to the 

purchaser or user in contract, in tort (including negligence), strict 

liability or otherwise for any special, indirect, incidental or conse-

quential damage or loss whatsoever, including but not limited to 

damage or loss of use of equipment, plant or power system, cost 

of capital, loss of power, additional expenses in the use of exist-

ing power facilities, or claims against the purchaser or user by its 

customers resulting from the use of the information, recommen-

dations and description contained herein. 

CSA is a registered trademark of the Canadian Standards Associ-

ation. National Electrical Code and NEC are registered trademarks 

of the National Fire Protection Association, Quincy, Mass. NEMA 

is the registered trademark and service mark of the National Elec-

trical Manufacturers Association.  Uniform Building Code (UBC) is 

a trademark of the International Conference of Building Officials 

(ICBO). UL is a federally registered trademark of the Underwriters 

Laboratories Inc.

Eaton Corporation

Electrical Group

1000 Cherrington Parkway

Moon Township, PA  15108l

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Содержание NTCEC2X20400WRU

























Отзывы: