Eaton i-on1000EX, Руководство по установке

Страница: 5 / 40

i-on1000EX
Page 1
1. Introduction
The i-on1000EX is a control unit for a hybrid
wired/wirefree alarm system intended for
domestic, commercial or industrial use.
The control unit comprises a steel case containing
the control unit PCB (printed circuit board), power
supply and space for up to two backup batteries.
The control unit PCB provides terminals for 10
buses. Each bus allows you to connect up to 25
peripheral devices using standard 7/0.2mm four-
wire alarm cable. The peripheral devices can be
any mixture of keypads or zone expanders (for
wireless or wired detectors).
Alternatively, for retrofit applications, a "pair
buses" option (displayed during initial
configuration) allows a bus to support double the
number of devices, up to a system maximum of
250. The
Pair Buses option allows you to pair
consecutively numbered buses (e.g. 0 and 1, or 4
and 5). In this case, you connect devices to the
first bus (e.g. 0) and leave the second bus in the
pair unconnected.
The control unit PCB also provides a range of
connectors for outputs and communicators.
The i-on1000EX can use i-kp01 keypads fitted
with firmware version 2.0 and above. The keypad
allows end users to set and unset the system, and
the installer to configure the control unit. The
keypad also contains an integral proximity tag
reader, which allows end users to control the
system without having to remember access
codes.
The following types of keypad are also available
for connection to the i-on1000EX:
KEY-K01 This keypad has no internal prox
reader, and is supplied in a square
format case.
KEY-KP01 This product, supplied in the same
case as the KEY-K01, has an
internal prox reader and also
provides terminals for an external
KEY-EP prox reader.
KEY-KPZ01 This product, supplied in the same
case as the KEY-K01, has an
internal prox reader and also
provides terminals for up to two
zones, a programmable output and
an external KEY-EP prox reader.
Note that the i-on1000EX must be fitted with at
least one wired keypad.
A range of wireless peripherals is available for
operation with the wireless expanders. These
include a door contact/universal transmitter, a
passive infra-red detector, smoke detector,
external siren, 4-button remote control, radio Hold
Up device and remote radio keypad.
This control unit is designed and approved to be
used as part of a Security Grade 3 system. The
control unit is also approved to operate as part of
a Security Grade 2 system.
If you install any radio devices, this will limit
approval to Security Grade 2.
Note: If the system uses radio HUDs and no other
radio transmitters, the system can be approved as
Grade 3, provided the rest of the system meets
Grade 3 standards.
Communications
The i-on1000EX provides sockets for an add-on
communication module. The available modules
are:
i-dig02
(ATS2) A switched telephone network
(PSTN) module that allows the
control unit to report alarm
information using standard
protocols such as Fast Format, SIA
and Contact ID, and can also send
text messages over the Public
Switched Telephone Network
(PSTN). The i-dig02 also allows
remote maintenance using
Eaton’s
Security Business Downloader
software.
i-sd02
(ATS2) A speech dialler and PSTN module
that allows the control unit to send
recorded speech messages and
report alarm information using
standard protocols such as Fast
Format, SIA and Contact ID. The
module can also send text
messages over the PSTN. The
i-sd02 also allows remote
maintenance using
Eaton’s Security
Business Downloader software.
i-gsm02
(ATS2) A GSM module that allows alarm
reporting, speech messaging and
SMS text messaging over the
mobile phone network. Note that a
SIM card is not included with the
module.
The control unit also provides outputs that can be
used to fit an external
“plug by” communicator.
To comply with EN50131 at Security Grade 2, you
must fit at least an ATS2 communicator (for
example, the i-dig02).
To be approved at Security Grade 3, use the plug-
by communicator outputs to connect the control
unit to an ATS4 communicator.
Partitions
The i-on1000EX allows you to create up to 50
partitions and allocate zones freely to one or more