manualshive.com logo in svg

Eaton Hydrokraft PVW 250, Руководство по эксплуатации

Поделиться
Скачать
Eaton Hydrokraft PVW 250 Скачать руководство пользователя страница 14

 

Product Description

13

HYDROKRAFT OPERATION MANUAL PVW 250+360

   E-PUIO_II001-E   April 2021   www.eaton.com

3.2.6 ES control 

This unit is used for flow adjustment. It has a 3-phase 

electric servo-motor, worm-gear and a switchbox with 

4 or (optional) 8 limit switches for different positions. 

A potentiometer for continuous adjustment and/or 

position monitoring is also available. Response times from 

zero to maximum depend on the ratio selected and on the 

(fixed) speed of the servo-motor, with the result that once 

the control is specified and built, response time are not 

variable in operation. Explosion Protection versions are 

also available. No Pressure/Power Limiter possible! 

A

–

System port

B

–

Inlet port

L1, L2 –

Drain port

L3

–

Vent port for vertical mounting

L3.1, L8 –

Air bleed port

L5

–

Oil filling plug

MA

–

Gauge port, system pressure 

ML

–

Gauge port, case pressure

1

–

Basic pump

2

–

Electric Motor for ES-control

Circuit shown is just an example, other options available. For circuit of individual pumps please contact technical support.

Содержание Hydrokraft PVW 250





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды