background image

INS #

Brand Logo  

reversed out of 

black

INS #

IB500021EN

Installation Instructions – Galleon / Galleonaire

Directives d’installation – Galleon / Galleonaire

Instrucciones de instalación – Galleon / Galleonaire

Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this 

product must be performed by a qualified electrician. This product must be installed in accordance 

with the applicable installation code by a person familiar with the construction and operation of the 

product and hazards involved. 

Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting 

any maintenance. Disconnect power at fuse or circuit breaker.

Risk of Fire- Refer to product label for specific minimum supply conductor requirements.

Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.

Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.

Failure to comply with these instructions may result in death, serious bodily injury and property damage.

WARNING

otee:

N

These instructions do not claim to cover all details or variations in the equipment, procedure, or process 

described, nor to provide directions for meeting every possible contingency during installation, operation 

or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for 

user’s purpose, please contact your nearest representative. 

otee:

N

Care must be taken not to set lighting fixture down on optical lenses or lift the fixture in the lens area. 

otee:

N

Specifications and dimensions subject to change without notice. 

DISCLAIMER OF LIABILITYe: Eaton assumes no liability for damages or losses of any kind that may arise from the 

improper, careless, or negligent installation, handling or use of this product.

 

NOTICEe:

 Green ground wire provided in proper location. Do not relocate.

ATTENTION Receiving Departmente:

 Note actual fixture description of any shortage or noticeable damage on 

delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be 

filed within 15 days of delivery. All damaged material, complete with original packing must be retained.

Safety

: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and 

ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under 

installation section. 

APPLICATIONS

: This lighting fixture is designed for outdoor lighting services, and should not be used in area 

of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to 

installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation 

and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and 

maintained according to the following recommendations.

Содержание Galleon














Отзывы: