Eaton FSO-2105 Скачать руководство пользователя страница 74

Страница: 74 / 96

Front Section

2. Align the shift block with the shift bar matching

the roll-pin holes and install the retaining roll pin.

Using tool E001044, push the roll pin until it is

flush with shift block hub.

Note:

Replace the roll pin by a new one.

624

Some through holes in housings are drilled for

machining purpose only and must be blocked later by

using cup-type metal expansion plugs.
During the transmission life, it is possible to happen

that some of those plugs should be removed and

reinstalled when servicing the unit.

Removal

1. In the housing, locate the expansion plug that

should be removed. Use the special device

E005005 and make a thread in the plug.

Expansion Plugs

639b

2. Use one retaining capscrew removed from the

housing and insert it into the plug, threading it

until it stays firmly in place.

EA046

3. Use the impact puller E003001 and adapter

E004002 to remove the capscrew and the plug

comes along.

EA169

Содержание FSO-2105

































































































Результаты поиска

Содержание FSO-2105

Отзывы:

Eaton FSO-2105, Руководство по обслуживанию, Страница: 74 / 96

Результаты поиска

Содержание FSO-2105

Отзывы: