Eaton FSO-2105 Скачать руководство пользователя страница 58

Страница: 58 / 96

Rear Section

5. Install the 5th speed gear on the mainshaft.

145

6. Install the retaining ball of the countershaft 5th

speed gear thrust washer on the countershaft.

Apply grease to hold the ball in place.

7. Install the 5th speed gear thrust washer on

the countershaft. Make sure to fit correctly the

retaining ball into the washer slot.

Note:

Install the thrust washer counterbore side

outward (facing the needle bearing).

8. Install the 5th speed gear needle bearing on the

countershaft.

148

147

143

9. Install the 5th speed gear on the countershaft.

139

10. Install the 5th speed ring synchronizer on the

countershaft..

Note:

The 5th speed synchronizer ring is NOT

coated with EFM II and is smaller than the

other rings.

11. Install the 5th/reverse synchronizer assembly on

the countershaft. Make sure it is installed in the

proper position.

Note:

Both the synchronizer sleeve sharp end

and the hub anti-escape relief should be

installed facing the 5th speed gear (refer

to “Synchronizer Assemblies”, in this

manual).

Make sure to properly slide the synchronizer ring

lugs into the hub key slots.

688

138

Содержание FSO-2105

































































































Результаты поиска

Содержание FSO-2105

Отзывы:

Eaton FSO-2105, Руководство по обслуживанию, Страница: 58 / 96

Результаты поиска

Содержание FSO-2105

Отзывы: