Eaton ePDU Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 27

Eaton ePDU Скачать руководство пользователя страница 8

Introduction

Eaton Advanced ePDU Troubleshooting Guide P-164000140—Rev 1

www.eaton.com/ePDU

3

.

Host Window

Page Title Tab

Application Header Bar

Main
Application
Page

Menu
Bar

Menu Selection Display

ePDU and Network Management
Card Identification Data

Refresh Bar Alarm Notification

Active
Alarm

Figure 3. ePDU Web Interface Opening Window

NOTE

The data that displays on the Web interface depends on the type of ePDU model
you are using.

The Menu Bar provides three groups of selections. All of these selections have options that can help you
troubleshoot problems.

l

Power Management

- Use the Power Management page to see current operating measurements for the ePDU that is reporting

data.

- Use the ePDU Outlets page to obtain information on individual outlets or factory groups. You can also use

this page to set individual outlets or factory groups to On, Off, or Reboot.

- Use the Active Alarms page to retrieve current alarms and see a list of alarms by date, time, and

description.

l

Logs and Notifications

- Use the Logs & Notifications menu selections to see a list of the most recent events or clear the log.

l

Settings

- Use Settings menu selections to correct problems arising from configuration settings.

Checking for E-mail Notifications with History Reports

Use the Web interface to set e-mail notifications (E-mail Notification page) and trap receivers (Trap Notification
page). E-mail notifications include comprehensive or filtered event history reports attached to daily e-mail
messages. The detailed data logs you receive can be useful for historical statistical analysis and diagnostics.

«
...
6
7
8
9
10
...
»

Содержание ePDU




























Отзывы:

Нет отзывов