background image

 

P/N 01-00510-00 

7500 Series Specifications 

Dimensions (overall)  

Height  

6.31”  (160 mm) 

Width 10.51” 

(267 

mm) 

Depth 5.25” 

(133 

mm) 

 

Weight 

• 

7 lbs (3.18 Kg)  

 

Voltage 

• 

24 VDC, -15% / +20% 

 

Power Consumption 

• 

16 Watts (without optional communication 
interface board) 

• 

22 Watts (with optional communication interface 
board) 

 

Heat Output 

• 

16 Watts (55 BTU/Hour) (without optional 
communication interface board) 

• 

22 Watts (75 BTU/Hour) (with optional 
communication interface board) 

 

Current 

• 

0.8 A (without optional communication interface 
board) 

• 

1.1 A (with optional communication interface 
board) 

 

Peak Inrush Current 

• 

16 A 

 

System Ambient Temperature 

• 

Operating:  0 - 50° C (32 - 122° F) 

• 

Non-operating:  -20 - 60° C (-4 - 140° F) 

 

System Vibration 

• 

Operating:  1 G at 10 - 500 Hz 

• 

Non-operating:  1 G at 10 - 500 Hz

 

 

System Shock 

• 

Operating:  30 G 

• 

Non-operating:  30 G

 

 

Relative Humidity 

• 

Operating:  20 - 90% non-condensing 

• 

Non-operating:  20 - 90% non-condensing 

 

Altitude 

• 

Operating:  10,000 ft (3,048 m) above sea level 

• 

Non-operating:  40,000 ft (12,192 m) above sea 
level 

 

Emissions 

• 

CISPR 22 Class A-Radiated and Conducted 

 

Noise Immunity 

• 

IEC 801-2,3,4,6,8 

• 

IEC 61000-4-2,3,4,5,6,8

 

 

Agency Certifications 

• 

CE Mark 

• 

UL/cUL and CSA Class I, Division 2, Groups A, 
B, C, D certified

 

 

Содержание Cutler-Hammer PanelMate ePro 7500 Series










Отзывы: