manualshive.com logo in svg

Eaton Cutler-Hammer Digitrip 3000, Инструкции по установке, эксплуатации и техническому обслуживанию, Страница: 75 / 92

Поделиться
Скачать
Eaton Cutler-Hammer Digitrip 3000 Скачать руководство пользователя страница 75

I.B. 17555C

Effective November 1999

Page A7

6.0

DRAWOUT OPERATION

6.1

INSERTING THE RELAY

Before the Digitrip 3001 is inserted into the Drawout 
Outer Case:

• Verify that all wiring is correct as shown in the wiring 

diagram.

• Set the DIP switches per Table 5.1 on page 36.

When inserting the DT3001 Drawout into the Drawout 
Outer Case, use the guides to align the exterior of the 
device chassis with the interior of the outer case. Slide 
the unit into the Case using the guides, pressing firmly 
until all four latches located on the sides of the device are 
seated and latched into place. Tabs on the DT3001 Dra-
wout Inner Chassis will prevent the inner chassis from 
being inserted upside down or being inserted into an 
outer case of another IQ product.

CAUTION

THE DT3001 INNER CHASSIS MUST BE FULLY 
INSERTED AND FULLY LATCHED IN TO ITS DRA-
WOUT OUTER CASE FOR PROPER OPERATION OF 
THE DEVICE.

When the unit is seated properly, the quick release but-
tons at the top and bottom of the unit will return to their 
non-compressed position. The device can now be 
secured in the outer case by inserting a utility locking ring 
in the provided slot.

6.2

REMOVING THE RELAY

WARNING

REMOVAL OF THE DIGITRIP 3001 INNER CHASSIS 
FROM THE DRAWOUT OUTER CASE EXPOSES LIVE 
PARTS, WHERE THE HAZARD OF A FATAL ELEC-
TRIC SHOCK IS PRESENT. ALWAYS DISCONNECT 
ANY CONTROL OR SOURCE POWER BEFORE 
TOUCHING ANYTHING ON THE INTERNAL OR 
EXTERNAL PARTS OF THE DRAWOUT OUTER 
CASE.

When removing the Inner Chassis from the Drawout 
Outer Case, first remove any locking ring that has been 
installed. Press the top and bottom quick release buttons 
simultaneously, and pull the relay out by its front panel.

Содержание Cutler-Hammer Digitrip 3000





























































































Отзывы:

Нет отзывов