background image

9

Installation procedure 

INSTALLATION AND OPERATION INSTRUCTIONS

   MN280103EN   March 2023   www.eaton.com

Figure 8 .  Connection diagram shows complete  

surge protection and illustrates bypass and 

disconnect switches

Figure 9 .  Terminal identification of  

Type NOVA NX-STS recloser

Refer to 

Figure 8

 and 

Figure 9

 for terminal identification 

of the NOVA NX-STS recloser.
Terminal connection to copper conductors only are 

recommended.
To rotate a flat-pad or eyebolt bushing terminal prior to 

connecting power line leads, loosen the pinch bolt on 

the terminals. After rotating the terminal, retighten the 

pinch bolt as follows: torque 3/8-16 pinch bolts to  

20–23 Nm (15–17 ft lb); torque 1/2-13 pinch bolts to 

39–42 Nm (29–31 ft lb).

7. 

Block ground sensing via the control panel.

8. 

Close source and load disconnect switches.

9. 

Close reclosers via control signal.

10. 

Open bypass switches.

11. 

Enable ground sensing, if applicable.

Removing recloser from service

 WARNING

HAZARDOUS VOLTAGE. ALWAYS USE A HOTSTICK WHEN 

WORKING WITH THIS EQUIPMENT. FAILURE TO DO SO COULD 

RESULT IN CONTACT WITH HIGH VOLTAGE, WHICH WILL CAUSE 

DEATH OR SEVERE PERSONAL INJURY.

 WARNING

HAZARDOUS VOLTAGE. DO NOT RELY ON THE OPEN POSITION OF 

THE YELLOW OPERATING HANDLE OR THE CONTACT POSITION 

INDICATOR; IT DOES NOT ENSURE THAT THE LINE HAS BEEN 

DE-ENERGIZED. ALWAYS ESTABLISH A VISIBLE DISCONNECT. 

FAILURE TO FOLLOW PROPER SAFETY PRACTICES CAN RESULT IN 

CONTACT WITH HIGH VOLTAGE, WHICH WILL CAUSE DEATH OR 

SEVERE PERSONAL INJURY.

1. 

Block ground tripping via the control panel. Refer 

to 

Service Information MN280095EN Form 7 

Microprocessor Based Pole Mount Recloser Control 

Installation and Operation Instructions

.

NOTICE

EQUIPMENT MISOPERATION. DISCONNECT ALL CONTROL POWER 

SOURCES PRIOR TO DISCONNECTING OR RECONNECTING THE 

CONTROL CABLE FROM THE CONTROL. FAILURE TO COMPLY 

CAN RESULT IN RECLOSER MISOPERATION AT THE TIME OF 

DISCONNECTION OR RECONNECTION OF THE CONTROL CABLE TO 

THE CONTROL.

2. 

Close all three bypass switches.

Note: 

If only one bypass switch is closed and the  

 

recloser is opened via the yellow operating  

 

handle, it is possible all three phases will trip  

 

based upon mode selection. 

3. 

Open the source and load disconnect switches.

4. 

Pull down all three yellow operating handles with a 

hotstick. The yellow operating handle is located under 

the recloser sleet hood.

 

If the recloser is set in single-phase trip/single-phase 

lockout mode, only one phase will open.

 

If the recloser is set in single-phase trip/three-phase 

lockout mode or three-phase trip/three-phase lockout 

mode, all three phases will open.

The control will sense that all three recloser phases  

are open.

NOTICE

DISCONNECT SWITCHES FOR AC SENSING AND POWER 

CONNECTIONS ARE NECESSARY TO ISOLATE THE CONTROL FOR 

TESTING AND SERVICING.

5. 

Disconnect the control battery.

6

4

2

5

3

1

Source

Load

Содержание Cooper Power NOVA NX-STS





























Отзывы: