background image

52 

 

U

SE

 

C

ONNECTIONS

 

 

INSTALLATION MUST BE CARRIED OUT EXCLUSIVELY BY QUALIFIED PERSONNEL. 

THE FIRST CONNECTION TO BE CARRIED OUT IS THE PROTECTION CONDUCTOR (EARTH CABLE), TO BE 

INSERTED IN THE TERMINAL MARKED 

THE UPS MUST NOT BE OPERATED WITHOUT BEING CONNECTED TO THE EARTHING SYSTEM. 

 

Warning: 

if the neutral (N) and phase (F) instructions are observed for the plugs and sockets, the UPS will not 

change the existing neutral arrangements when inserted in a system. The resistance on the neutral connection 
is less than 0.1 ohm. 
A differential switch placed upstream will also be triggered for a fault occurring downstream of the UPS. The 
sensitivity of this switch has to take into account the leakage current of the unit (approx. 2 mA) and of the load 
which are added together on the UPS earth conductor. 
The neutral arrangements will only be changed if an isolation transformer is connected or when the UPS is 
operating with the neutral isolated upstream. 
Avoid connecting the output neutral to the input neutral or to earth as this could damage the UPS . 

 

For the mains and load connections follow the instructions set out below: 

1.

 

Install a 32A magneto-thermal switch with B or C trip curve upstream of the equipment. 

 
 
 
 
 
 
2.

 

The terminals to be used for the connection of the input and 
output lines are located inside the IN/OUT connections 
drawer. Undo the screw securing the connections drawer 
located on the right-hand side of the drawer (see figure at 
side). 

 
 
 
 
 
 
 
 
 
 
 
 
3.

 

Pull the drawer out as much as is needed for the terminals to 
be easily accessible (see figure at side). WARNING: the 
drawer has a locking system to prevent it being pulled out 
completely. Do not try to remove the drawer completely. 

 

Содержание 5000 VA

































Отзывы: