Eaton 3S700D, Инструкция по установке и эксплуатации

Страница: 6 / 42

6
E
N
gl
IS
h
Operating conditions
l
This product is an U ninterruptible
P ower S upply ( UPS ) for computers
and their peripherals, television
sets, stereo systems and video
recorders... It must not be used to
supply other electrical equipment
(lighting, heating, household
appliances, etc.).
UPS connections
l
Connect the UPS 1 to the
AC-power system via a wall outlet
with an earth connector, using the
attached cord for a
UPS with FR/
DIN sockets or with the supply cord
of your computer for a
UPS with
IEC sockets (see figure A).
l
Plug critical equipment
(computer, monitor, modem,
etc.) into the outlets
6 providing
battery backup power and surge
protection (see figure B), taking
care not to exceed the rated current
indicated in amperes.
l
Other devices (printer, scanner,
fax, etc.) can be connect to the
filtered outlets 5 that provide
surge protection (see figure B). The
filtered outlets are not backed up
by battery power in the event of a
power outage.
l
Optional Internet modem /
Network connection:
A modem or Ethernet data line
can be protected against surges by
connecting it via the
UPS . Connect
the existing device cable between
the wall outlet and the
UPS
, and
use a similar cable between the
UPS and the device, as indicated in
figure C (cable not supplied).
l
Optional USB connection:
The
UPS
devices can be connected
to the computer using the USB
cable
4 supplied.
l
Download software at
powerquality.eaton.com.
l
Register warranty at
powerquality.eaton.com.
l
Battery charge: The UPS
charges the battery as soon as it is
connected to the AC outlet, whether
button
8 is pressed or not. When
used for the first time, the battery
will only provide its maximum
autonomy after it has been charged
for 8 hours. It is recommended that
the UPS be permanently connected
to the AC power supply to ensure
the best possible autonomy.
l
Switching-on the UPS : press
button 8 for about 1 second.
l
Filtered outlets
5
without
battery backup: Equipment
connected to these outlets is
supplied as soon as the AC cord is
plugged in. They are not affected by
button
8 .
l
Battery backup outlets
6 :
Equipment connected to these
outlets is supplied as soon as
button
8 turns green (see figure
E). These outlets can be turned on
even if the UPS is not connected to
AC power (button 8 flashes).
l
AC-power disturbance:
If AC
power is disturbed or fails, the UPS
continues to operate on battery
power. Button
8 flashes green.
In normal mode, the audio alarm
beeps every five seconds, then
every two seconds when the end of
battery backup time is near.
l
If the power outage lasts longer
than the battery backup time, the
UPS shuts down and automatically
restarts when power is restored.
Following a complete discharge, a
few hours are required to recharge
the battery back to full backup time.
l
To save battery power, it is
possible to press button 8 to cut
the supply of power to the devices
connected to the battery backup
outlets.
l
Lightning protection: All outlets,
whether backed up or simply
filtered, include surge protection,
whatever the position of button 8 .
l
Shutdown of the battery backup
outlets 6 : Press button 8 for
more than two seconds.
Battery disposal and safety
l
Caution. Battery service life is
reduced by 50 % for every ten
degrees above 25 °C.
l
The battery elements must be
replaced exclusively by qualified
personnel (risk of electrocution)
,
with new elements approved by
EATON to ensure correct operation
of the
UPS
.
l
The battery must be disposed
of in accordance with applicable
regulations. To remove the battery
elements, shut down the UPS
(button 8 OFF), remove the power
cord and proceed as indicated in
page 4 "Battery change".
6 5
9
8
7
Operation
5 : Filtered outlets.
6 : Battery backup outlets.
7 : LED ON indicate a UPS fault.
8 : ON/OFF button for the battery
backup outlets.
9 : Protection circuit breaker.