Eaton Compressor POLAR AIR P01IXXXP07V080VXXXX Скачать руководство пользователя | Manualshive

Страница: 22 / 39

background image

Splash Lubricated, Air Compressor Pumps

This manual contains very important information to know and understand. This is provided for SAFETY and to
PREVENT EQUIPMENT PROBLEMS. To help understand this information, observe the following:

Danger indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.

Warning indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

Caution indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.

Notice indicates important information, that if not followed, may cause damage to
equipment.

DANGER

WARNING

CAUTION

NOTICE

Read all manuals included with this product carefully. Be
thoroughly familiar with the controls and the proper use of the
equipment.

1.

Allow only trained, authorized persons who have read and understood these operating instructions to use

this compressor pump. Failure to follow the instructions, procedures and safety precautions in this manual

can result in accidents and injuries.

2.

NEVER

start or operate the compressor pump under unsafe conditions. Tag the compressor, disconnect and

lock out all power to it to prevent accidental start-up until the condition is corrected.

3. Install, use and operate the compressor pump only in full compliance with all pertinent OSHA regulations

and all applicable Federal, State & Local codes, standards and regulations.

4.

NEVER

modify the compressor pump and/or controls in any way.

5. Keep a first aid kit in a convenient place. Seek medical assistance promptly in case of injury. Avoid infection

by caring for any small cuts and burns promptly.

1.

NEVER

use air from this compressor pump for breathable air except in full compliance with OSHA Standards

29 CFR 1910 and any other Federal, State or Local codes or regulations.

Death or serious injury can result from inhaling compressed air
without using proper safety equipment. See OSHA standards on safety
equipment.

DANGER

Safety Information

Basic Guidelines

Breathable Air

3

«
...
20
21
22
23
24
...
»

Содержание POLAR AIR P01IXXXP07V080VXXXX








































Отзывы:

Нет отзывов

Похожие инструкции для POLAR AIR P01IXXXP07V080VXXXX

Бренд: Daikin Страницы: 51

Бренд: Clarke Страницы: 20

pluscom Bock EX-HG12P

Бренд: GEA Страницы: 44

Бренд: Kobalt Страницы: 8

Бренд: Kobalt Страницы: 8

Бренд: Kobalt Страницы: 24

Бренд: Heavy Duty Power Systems Страницы: 9

Бренд: J.E. Adams Страницы: 16

Quincy Air Master QT-10

Бренд: EnPro Страницы: 18

Бренд: Ryobi Страницы: 96

Бренд: PUMP'IN Страницы: 18

Бренд: L&W Compressors Страницы: 207

Бренд: Danfoss Страницы: 2

Бренд: California Air Tools Страницы: 15

Бренд: Sullivan-Palatek Страницы: 100

Бренд: Bacharach Страницы: 28

Бренд: Danfoss Страницы: 58

Бренд: RAMVAC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды