Easyguard EC002 Series Скачать руководство пользователя страница 17

Страница: 17 / 25

Lock

Unlock

+12V

Door lock switch

key cylinder

Orange

White

Yellow

Orange/black

White/black

Yellow/black

COM

(Lock signal)

(Unlock signal)

Lock

Unlock

Drivers door

EC002 output

central car lock control unit

BCM

12V (vehicle fused co12V)

not used
(insulate separately)

Lock resistor

(if required)

Unlock resistor

(if required)

Type H: Negative (-) multiplex. Same as Type G system, but uses (-) pulse instead.

Single wire negative central locking

Single wire, negative lock, negative unlock.

Two potential (resistor may require) negative trigger.

Single-resistor style: if one resistor is used in the door lock switch/key cylinder, the wire will pulse ground

in one direction and resistance to ground when operated in the opposite direction.

Two resistor type: if two resistors are used in the factory door lock switch/key cylinder, the switch/key

cylinder will read resistance to ground in both directions.

Determining the proper resistor values: to determine the resistor values, the door lock switch/key cylinder

must be isolated from the factory door lock system. For testing, use a calibrated digital multi-meter that is

set to ohms.

IMPORTANT:

To ensure an accurate resistance reading, do not touch the resistor or leads during testing.

1.Cut the output wire from the door lock switch/key cylinder in half;

2.Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable ground

source. Some good ground references are the ground input source to the door lock switch/key cylinder, or

the battery ground.

3.Operate the door lock switch/key cylinder in both directions to determine the resistor values. If the multi-

meter displays zero resistance in one direction, no resistor is need for that direction.

4.Once the resistor value(s) is determined, refer to the wring diagram for proper wiring.

EC002 output

central car lock control unit

Lock

Unlock

Door lock switch

key cylinder

Orange

White

Yellow

Orange/black

White/black

Yellow/black

COM

(Lock signal)

(Unlock signal)

Lock

Unlock

Drivers door

BCM

not used
(insulate separately)

Lock resistor

(if required)

Unlock resistor

(if required)

Chassis Ground

-30-

EASYGUARD

Electronics

All

right reserved.

-29-

EASYGUARD

Electronics

All

right reserved.

Содержание EC002 Series


























Результаты поиска

Содержание EC002 Series

Отзывы:

Похожие инструкции для EC002 Series

Бренды по названию

Популярные бренды

Easyguard EC002 Series, Руководство пользователя

Результаты поиска

Содержание EC002 Series

Отзывы:

Похожие инструкции для EC002 Series

Бренды по названию

Популярные бренды