Eastwood 58221 Скачать руководство пользователя страница 10

Страница: 10 / 12

Eastwood Technical Assistance: 800.343.9353 >> [email protected]

PROBLEM

CAUSE

CORRECTION

Plasma Cutter Will

Not Power Up;

GREEN Indicator

Does Not Illuminate

Plasma Cutter not plugged into

proper power supply

Check power supply. The VERSA-CUT 60 requires a properly grounded,

120 Volt AC, 20 Amp or 240 Volt AC, 50 Amp circuit.

Power supply breaker tripped

Reset breaker.

Power switch not fully on

Check that Power Switch is fully “ON”, GREEN indicator illuminates.

Duty Cycle exceeded; Plasma

Cutter overheated;

AMBER indicator illuminated

Turn Power switch OFF, allow Plasma Cutter 15 minutes to cool then re-try.

Plasma Cutter

Shuts Off During

Use While the

Power Switch is On,

AMBER Indicator

Illuminated

Plasma Cutter Duty Cycle has

been exceeded

Turn Power switch OFF, allow Plasma Cutter 15 minutes to cool then re-try.

Water Drips from

the Rear Underside

of the Unit

The internal Moisture Trap is draining

No action required. This feature activates whenever the compressed air

source is disconnected.

TROUBLESHOOTING: OPERATIONAL PROBLEMS

Содержание 58221













Результаты поиска

Содержание 58221

Отзывы:

Похожие инструкции для 58221

Бренды по названию

Популярные бренды

Eastwood 58221, Инструкции по сборке и эксплуатации

Результаты поиска

Содержание 58221

Отзывы:

Похожие инструкции для 58221

Бренды по названию

Популярные бренды