manualshive.com logo in svg

Eastwood 31847, Инструкция по эксплуатации

Поделиться
Скачать
Eastwood 31847 Скачать руководство пользователя страница 2

2

 

Eastwood Technical Assistance: 800.343.9353  >>  [email protected]

The 

EASTWOOD 3”, ADJUSTABLE HEAD CUT-OFF TOOL

 offers a full 50° (+- 25° ) of additional head 

angle adjustability to safely access areas difficult to reach with ordinary pneumatic Cut-Off tools. The 
reversible feature allows the user to choose the direction of the resulting “spark-shower” to avoid 
injury and property damage. A high-torque, ball bearing supported, 4 vane motor provides smooth 
operation and long life. Speed is easily controlled with a variable speed control knob while motor 
activation is by paddle control.

CONTENTS

(1)

  3”, Adjustable Head Cut-Off Tool

(1)

  11mm Flat Wrench

(1)

  17mm Flat Wrench

(1)

  4mm Hex Key Wrench

(1)

  3” Cut-Off Wheel

(1)

  1/4” MNPT, Male Quick-Disconnect Inlet Fitting

SPECIFICATIONS

RPM:

 16,000 free speed

Air Consumption:

 3.6 CFM [100 L/min] 

Inlet Thread Size:

 1/4” FNPT

3 Position, Adjustable Head; set straight, 25° up or 25° down
Variable speed, 4 vane, ball bearing air motor
Rear Exhaust

Replacement Cut-Off Wheel Size:

 

3” x 3/8 [9.5mm]” Arbor, minimum 16,000 RPM.

Содержание 31847













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды