background image

 

- 21 - 

Fault LED on, audible buzzer 
persistently alarm, the fault code 
is 50-54 

Over load 

Please check the load level and 
disconnect the noncritical devices, 
recount the total capacity of your load 
and reduce the load to the UPS. 
Please check whether the load device has 
fault or not? 

Fault LED on, audible buzzer 
persistently alarm, the fault code 
is 55-59 

Input NTC fault 

Please contact the supplier. 

Fault LED on, audible buzzer 
persistently alarm, the fault code 
is 60-64 

Power fault 

Please Check whether the input & output 
power normal or not, contact the supplier 
if it is abnormal. 

Fault LED on, audible buzzer 
persistently alarm, the fault code 
is 65-69 

Input fuse fault 

Please check if the input fuse is burnt. 
Replace the old fuse and restart the UPS. 
If failure remains, please contact the 
supplier. 

Fault LED on, audible buzzer 
Persistently alarm, fan icon in 
the LCD flickers 

Fan fault 

Please check whether the fans connect 
well, is the fan plugged and is the fan 
broken? If all above condition is OK, 
please contact the supplier. 

UPS fail to start when operate 
“On” key. 

 

Pressing time too short 

Please press the power key more than 2 
seconds to start the UPS. 

The input connection 
is not ready or 
UPS internal battery 
disconnect   

Please connect the input well, if the 
battery voltage is too low, please 
disconnect the input and start the UPS 
with no-load. 

UPS internal system 
fault   

please contact the supplier. 

Back up time become short 

Battery undercharge 

Please keep the UPS battery recharging 
more than 3 hours   

UPS overload 

Please check the load level and 
disconnect the noncritical devices, 

Battery maturing, 
capacity descend. 

Please change new battery, contact your 
supplier to get the new battery and spare 
parts. 

UPS doesn’t have any power go 
through even main power on. 

UPS input breaker 
disconnects. 

Please reset the circuit breaker by 
manual. 

7. Attention of battery disposal 

Please take off your ring, watch and other metals before operate the batteries.

 

If you want to change the battery cable, please purchase the material from our local service center or 

distributors, to avoid heating or spark due to the inadequate power capacity, and even causing fire. 

Don’t dispose of the battery or battery pack near or into fire, otherwise it will explode and injure 

person. 

Содержание EA900IIRT 1000VA


























Отзывы: