3
contact or in contact with anything other than the plug-
in electronics (Chargeberry).
—
Never use or touch the product if it is damaged or does
not function properly.
—
In case of a critical error, the charger will alert the user
with a warning sound and flashing red light on the light
strip. Turn off the power and remove the charging cable
from the Charging Robot. The power can then be turned
back on if necessary. The flashing red light will continue,
but the warning sound will stop when the charging cable
is disconnected. The charger is blocked from further
use, cannot be reset and has to be replaced. Contact
customer support.
CAUTION
—
If a fire occurs, use CO
2
for extinguishing. To extinguish
it with water or foam, the system must be first de-
energized (electrically disconnected).
—
Never clean the product with high pressure or running
water.
—
Do not immerse the product in water or other liquids.
—
Never touch the contacts of the Type 2 socket and never
insert foreign objects into the product.
—
Never use the charging cable if it is damaged or if the
connections are wet or dirty.
—
Do not use extension cords or adapters in combination
with the product.
—
Avoid direct sunlight for optimal operation in all weather
conditions.
—
Do not use the product near strong electromagnetic
fields or in the direct vicinity of radio transmitters.
—
The product must be installed on a permanent location.
The connections of the Chargeberry and backplate are
designed for a limited number of plugging cycles.
—
Make sure that children do not play with the product.
—
Make sure the charging cable does not cause a tripping
hazard or risk being run over by a car.
—
The charging cable must only be removed from the
Charging Robot by pulling the plug handle, not by
pulling the cable.
Additional important information
Simplified Declaration of Conformity
Hereby, Easee ASA declares that Charge Core, Charge Lite
and Plug & Play defined in this manual are in conformance
with the EU Radio Equipment Directive 2014/53/EU and
RoHS Directive 2011/65/EU.
Hereby, Easee ASA declares that Easee Ready is in
compliance with the Low Voltage Directive 2014/35/EU and
RoHS Directive 2011/65/EU.
Hereby, Easee ASA declares that Easee One and Charge
Core defined in this manual and sold in the UK after
January 2023 are in compliance with the UK Radio
Equipment Regulations 2017 and RoHS regulations 2012.
The full text of the EU Declaration of Conformity is
available at:
The full text of the UK Declaration of Conformity and the
UK Smart Charging Regulations Statement of Compliance
and Technical File are available at the following internet
address:
Transportation
The product should always be transported within its
original packaging. No other items should be stored on top
of the box other than Easee chargers. Should the box be
dropped or otherwise impacted, a visual inspection should
be done in order to verify potential damage.
Storage
The electronics are sealed and will not get damaged if
stored in humid areas. However, in order to preserve the
packaging and its contents, we recommend storage in a
tempered, dry and well-ventilated area. Relative humidity
should not exceed 80% and no corrosive gas should be
present. Storage or transportation environment must never
exceed the limits provided in the Technical specifications.
Dismounting
Perform a factory reset of the device before powering it
down. This is done via the Installer App. Dismounting of
the backplate shall only be performed by an authorised
electrician. The power supply to the charger must be
isolated before dismounting starts. Use the installation
guide and follow the steps in reverse in order to dismount
the product in the correct order.
Data protection
When the product connects to the Internet, personal data is
sent to Easee ASA. You will receive more information about
data protection during the configuration of your Charging
Robot.
Waste handle
A crossed-out dustbin (WEEE symbol) indicates that a
product and its accessories must not be disposed of in
household waste at the end of their lifecycle.
EN
