EarthQuake Victory Скачать руководство пользователя страница 18

Страница: 18 / 34

Operator’s Manual

Rototiller Victory

For additional information email

[email protected]

or call 800-345-6007 M-F 8-5

BOTTOM OF SQUARE

RESTS ON DIPSTICK PLUG

2¾”

ACCEPTABLE GREASE LEVEL

ADD GREASE

3¼”

Check tiller transmission grease:

Check the grease level annually. To check the grease level:

1. Cut out one of the cardboard stencils on page 27 of this

manual. Take that dipstick cut-out and glue/tape it to a

piece of cardboard cut out to match the stencil.

2. Tiller must first be run for approximately 30 minutes to

warm up grease for a proper measurement. Once warm

let sit 5 minutes to allow grease to settle.

3. Move tiller to level ground, making sure the transmission

cover plate is level.

4. Remove the gear case dipstick located between the

handle bar mounts and the engine mount.

SEE FIGURE 14

5. Insert the dipstick cut-out created in step 1 into the

hole in the transmission cover plate so the top square is

resting on the cover plate.

SEE FIGURE 15

6. Remove the dipstick cut-out and check grease level.

If level is in the bottom ADD area or not present, add

grease in 200ml increments until grease level reaches a

proper level reading (between 1” - 1 3/4” down from top

of fill hole).

DO NOT OVERFILL.

The slashed, acceptable

grease level area on the dipstick cut-out has a 200ml

range.

NOTE: The front wheel transmission and rear tine

transmission share a common reservoir.

Recommended grease is Mystic 00, or equivalent,

transmission grease. Oil must have an API -

E.P (extreme pressure) rating of GL4 or lower.

Higher E.P. rating (ie - GL5, GL6 etc) will cause

the bronze components to soften. For partial

fill-ups ( a few ozs or less) use SAE 140W or 85W

gear oil or SAE 80W-90 weight gear oil with a API

rating of GL4 or GL5. When replacing grease, the

tiller transmission holds 18-22 ounces. DO NOT

OVERFILL.

FIGURE 14

FIGURE 15

CAUTION

GEAR CASE

DIPSTICK

GEAR CASE

DIPSTICK

GEAR CASE

DIPSTICK HOLE

TRANSMISSION

COVER PLATE

DO NOT PUT ENGINE

OIL IN TRANSMISSION.

LUBRICANT IS

INSTALLED BY

MANUFACTURER.

Содержание Victory



































Результаты поиска

Содержание Victory

Отзывы:

Похожие инструкции для Victory

Бренды по названию

Популярные бренды

EarthQuake Victory, Руководство оператора

Результаты поиска

Содержание Victory

Отзывы:

Похожие инструкции для Victory

Бренды по названию

Популярные бренды