EarthQuake Victory Скачать руководство пользователя страница 13

Страница: 13 / 34

For additional information email

[email protected]

or call 800-345-6007 M-F 8-5

Operator’s Manual

Rototiller Victory

FORWARD CABLE

REVERSE CABLE

LOWER JAM NUT

UPPER JAM NUT

FIGURE 8

Depth Regulator Lever

Tilling depth is controlled by the height of the depth regulator

lever.

SEE FIGURE 9

Adjust tilling depth as follows:

1. Remove lock pin.
2. Raise the depth regulator lever to position tines at

chosen tilling depth.

3. Align hole in depth regulator lever with hole in depth

regulator bracket and insert lock pin.

NOTE: Depth Regulator Lever Down = Shallower tilling.

Place the lock pin in the top hole of the depth

regulator lever for shallowest tilling.

Depth Regulator Lever Up = Deeper tilling. Place

the lock pin in the bottom hole of the depth

regulator lever for deepest tilling.

LOCK PIN

DEPTH REGULATOR

BRACKET

TRANSPORT HOLE

SHALLOW DIGGING

DEEPEST DIGGING

DEPTH

REGULATOR

LEVER

FIGURE 9

EXTREME CAUTION MUST BE TAKEN IN SELECTING

TILLING DEPTH. IF YOU ATTEMPT TO TILL TOO DEEPLY

FOR SOIL CONDITIONS, THAT IS, WITH THE DEPTH

REGULATOR LEVER IN TOO HIGH A POSITION, LOSS OF

CONTROL AND INJURY TO PERSONNEL CAN OCCUR.
ALWAYS SET THE DEPTH REGULATOR LEVER IN THE

TRANSPORT POSITION BEFORE STARTING ENGINE.

PLACE THE DETENT PIN IN THE HIGHEST HOLE OF THE

DEPTH REGULATOR LEVER

WARNING

Wheel Lock Pins
To place wheels in free-wheel position do as follows:

NOTE: This allows wheels to turn freely on the axle for

easy transportation.

1. Remove lock pin. Slide wheel inward toward machine.

SEE FIGURE 10 (Next Page)

2. Insert lock pin through the axle hole only, fold lock ring

to secure pin to axle.

3. Repeat for other wheel.

To place wheels in tilling position do as follows:

NOTE: This locks wheels to the axle so they are able to

propel the machine forward while in use.

1. Remove lock pin. Slide wheel slightly outward away from

machine. Align hole in axle with hole in wheel hub.

SEE FIGURE 11(Next Page)

2. Insert lock pin through both holes, fold lock pin ring to

secure pin to axle.

3. Repeat for other wheel.

NOTE: Always have both wheel lock pins in or out. Do not

operate tiller with only one wheel locked.

Содержание Victory



































Результаты поиска

Содержание Victory

Отзывы:

Похожие инструкции для Victory

Бренды по названию

Популярные бренды

EarthQuake Victory, Руководство оператора

Результаты поиска

Содержание Victory

Отзывы:

Похожие инструкции для Victory

Бренды по названию

Популярные бренды