background image

Operator's Manual

Rolling High-Wheel String Trimmer 600050 Series

Get parts online at 

www.getearthquake.com

 or call 800-345-6007 M-F 8-5

5

sloPe oPeRATIon

Slopes are a major factor related to slip and fall accidents which 

can result in severe injury. All slopes require extra caution. If you 

feel uneasy on a slope, do not trim it. Do trim across the face of 

slopes; never up and down. Do not trim excessively steep slopes 

(maximum 15 degrees) or areas where the ground is very rough. 

See the “Slope Guide” in the back of this manual to check a slope. 

Exercise extreme caution when changing direction on slopes.
• 

Remove objects such as rocks, tree limbs, etc.

• 

Watch for holes, ruts, or bumps. Tall grass can hide ob-

stacles.

• 

Do not trim near drop-offs, ditches, or embankments.  The 

operator could lose footing or balance.

• 

Do not trim excessively steep slopes.

• 

Do not trim on wet grass. Reduced footing could cause 

slipping.

cHIldRen

Tragic accidents can occur if the operator is not alert to the 

presence of children. Children are often attracted to the trim-

mer and the trimming activity. Never assume that children will 

remain where you last saw them. 

•    Keep  children  out  of  the  trimming  area  and  under  the 

watchful care of a responsible adult. 

•    Be alert and turn trimmer off if children enter the area.
•    Before and while moving backwards, look behind and down 

for small children.

•    Never allow children to operate the trimmer. 
•    Use extra care when approaching blind corners, shrubs, trees, 

or other objects that may obscure  vision.

seRVIce

•  Use extra care in handling gasoline and other fuels. They are 

flammable and vapors are explosive.

•   Use only an approved container.
•   Never remove gas cap or add fuel with the engine running. 

Allow engine to cool before refueling. Do not smoke.

•   Fill fuel tank outdoors with extreme care. Never fill fuel tank 

indoors or near appliances with pilot lights, heaters, or other 

ignition sources. Replace fuel cap securely. If fuel is spilled, 

do not start the engine but move product and fuel container 

from area. Clean up spilled fuel and allow to evaporate.

•   Never store the machine or fuel container inside where there 

is an open flame (such as a water heater), or other ignition 

source.

•  If the fuel has to be drained, this should be done 

outdoors. The drained fuel should be stored in a container 

specifically designed for fuel storage or it should be 

disposed of carefully.

•    engines give off carbon monoxide, an odorless, colorless, 

poison gas.  Breathing carbon monoxide can cause 

nausea, fainting or death.  Always start and run engine 

outdoors.  Do not start or run engine in an enclosed area, 

even if doors or windows are open.  

•    Never make adjustments or repairs with the engine (motor) 

running. Disconnect the spark plug wire, and keep the wire 

away from the plug to prevent accidental starting (remove 

the ignition key if equipped with an electric start). Always 

wear eye protection when you make adjustments or repairs.

•    Check the trimmer head and engine mounting bolts at 

frequent intervals for proper tightness. 

•    Keep all nuts and bolts tight and keep equipment in good 

condition. Check mounting hardware on trimmer head every 

time you change trimmer line and prior to each use.

•    Never tamper with safety devices. Check their proper 

operation regularly.

•    When servicing or repairing the trimmer, do not tip the machine 

over or up unless specifically instructed to do so in this Manual. 

Service and repair procedures can be done with the trimmer 

in an upright position. Some procedures will be easier if the 

machine is lifted on a raised platform or working surface.

•    To reduce fire hazard, keep trimmer free of grass, leaves, or 

other debris build-up. Clean up oil or fuel spillage. Allow 

trimmer to cool before storing.

•    Stop and inspect the equipment if you strike an object. 

Repair, if necessary, before restarting. 

•    Always disconnect spark plug wire before cleaning, repairing, 

or adjusting. 

•    Do not change the engine governor setting or over-speed 

the engine. 

•    Clean and replace safety and instruction decals as necessary.
•    To guard against engine over-heating, always have engine 

debris filter mounted and clean.

•    Inspect trimmer before storage. When not in use,  disconnect 

spark plug lead and store indoors in a dry place locked or 

otherwise inaccessible to children.

•    Use only original equipment or authorized replacement 

parts.

•    Never replace the cutting lines with metal parts. 
•    When storing gasoline or equipment with fuel in the tank, 

store away from furnaces, stoves, water heaters or other 

appliances that have a pilot light or other ignition source 

because they can ignite gasoline vapors.  

Содержание 600050V





























Отзывы: