EarthQuake 5055 6 HP Скачать руководство пользователя | Manualshive

Страница: 19 / 28

background image

OPERATING INSTRUCTIONS ANd PARTS ExPlOSIONS

CRT Models

Page 1

800-345-6007

PROBlEm

REmEdY/ACTION

Belts squeal in neutral and/or reverse

• Adjust forward belt guide:
  -  turn engine off and allow muffler to cool
  -  disconnect spark plug wire and secure from spark plug
  -  remove belt guard
  -  pull down on drive safety control levers
  -  manually bend forward belt guide so there is 1/16 inch

or less clearance between belt guide and belt
- replace belt guard and spark plug wire

Belts squeal in forward operation

• Adjust tabs on the reverse belt guide
  -  turn engine off and allow muffler to cool
  -  disconnect spark plug wire and secure from spark plug
  -  release drive safety control levers to neutral position
  -  remove belt guard
  -  adjust tabs of reverse belt guide:
    while drive safety control levers are released, bend

metal tabs on reverse belt guide to 1/64 inch or less

clearance from reverse belt
- replace belt guard and spark plug wire

Excessive heat build up in transmission/tine
area during tilling

• Remove vegetation by following instructions in clean

Tine Axle Shaft of Normal care section.

FOLLOW ALL SAFETY INSTRUcTIONS
• check transmission fluid and fill if needed

«
...
17
18
19
20
21
...
»

Содержание 5055 6 HP





























Отзывы:

Нет отзывов

Похожие инструкции для 5055 6 HP

Бренд: EarthQuake Страницы: 13

Бренд: Titan Pro Страницы: 8

Бренд: SMC Networks Страницы: 192

Бренд: EarthQuake Страницы: 28

Бренд: The Handy Страницы: 21

Бренд: The Handy Страницы: 24

Therminator 057.029.1

Бренд: Blichmann Engineering Страницы: 7

Бренд: MTD Страницы: 24

Бренд: Elkay Страницы: 2

Бренд: sunjoe Страницы: 16

Бренд: VALERA Страницы: 2

Бренд: YATO Страницы: 108

Бренд: Gardol Страницы: 48

Бренд: Barco Страницы: 102

Ultracool Superplus series

Бренд: Lauda Страницы: 23

Бренд: Samsung Страницы: 52

Бренд: Husqvarna Страницы: 16

Бренд: Husqvarna Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды