EarthLinked TXV Kit Скачать руководство пользователя | Manualshive

Страница: 19 / 28

background image

TXV–CLP-KIT (07/15)

Page 19

The TXV control box is field positioned external to the vertical (upflow or downflow) cased coil and
fastened to a solid mounting surface immediately adjacent to the cased coil as shown typically in
Figure 11a. Locate the TXV control box to allow a service access of at least 12 inches in front of
the box to adjust the TXV control.

Figure 11a. TXV Control installed near Cased Coil (Vertical Application)

Important!

The TXV control box must be located no more than 3-1/2 feet from the
suction tube stub out on the air handler. The TXV control box must be
mounted above the cased coil tubing stub outs as shown.

«
...
17
18
19
20
21
...
»

Содержание TXV Kit





























Отзывы:

Нет отзывов

Похожие инструкции для TXV Kit

Бренд: Campbell Hausfeld Страницы: 24

Craftsman 919.727560

Бренд: Sears Страницы: 20

Бренд: J.E. Adams Страницы: 16

Бренд: Strongway Страницы: 25

Бренд: Sakura Страницы: 11

Бренд: Arnott Страницы: 5

Бренд: WilTec Страницы: 12

Бренд: Universal Audio Страницы: 24

Бренд: North American Tool Industries Страницы: 10

Бренд: Campbell Hausfeld Страницы: 20

Бренд: Ecoair Страницы: 53

Бренд: GEA Bock Страницы: 28

Teich-Aire KM Series

Бренд: Kasco Страницы: 11

Бренд: Vector Страницы: 8

Бренд: Johnson Controls Страницы: 56

RABD255/100/2.5

Бренд: Ross Страницы: 12

Бренд: Powerex Страницы: 8

Бренд: Metabo HPT Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды