EarthCore Isokern MAXIMUS 82L120 Скачать руководство пользователя

Страница: 1 / 69

—

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity

of this or any other appliance.

—

WHAT TO DO IFYOU SMELL GAS

•

Do not try to light any appliance.

•

Leave the building immediately.

•

Do not touch any electrical switch; do not

use any phone in your building.

•

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call

the fire department.

—

Installation and service must be performed

by a qualified installer, service agency or the

gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warning exactly could

result in serious injury, death, or property damage.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference

Do not install the Isokern MAXIMUS Linear Series

Gas Fireplace in a manufactured home or mobile

home or recreational vehicle.

Isokern® MAXIMUS Linear Series

Open Front Gas Fireplace and Chimney System

Installation, Operation, Maintenance and Owner’s Manual

Isokern Models: 82L48, 82L72, 82L96 & 82L120

A PRODUCT OF EARTHCORE® INDUSTRIES, LLC

IMPORTANT

: This manual contains assembly rules, installation steps and guidelines, and use and maintenance instructions

for Isokern MAXIMUS Linear Series Open Front gas appliances. This manual must become the property of and be reviewed

by all current and future users of this product. It is the responsibility of the distributor, general contractor, and the installer

of this product that the instructions in this manual are followed exactly and, further that the allowed gas log appliance used

in this product be installed in strict accordance with the gas log manufacturer’s listing and explicit installation and operation

instructions.

Be Sure to Read Entire Manual Before Beginning Construction.

Contents of this manual may change without prior notification.

PFS Report No. F19 -161

USA: ANSI Z21.50 - 2019

ICC Report No. ESR - 4873

Issued: December 2021

Revision: 001

THESE FIREPLACES ARE DESIGNED FOR USE WITH:

PROPANE (LP) OR NATURAL GAS (NG), ONLY

THIS MANUAL CAN ONLY BE REPRODUCED IN ITS ENTIRETY

—

This appliance complies with National Safety and

is tested and listed to ANSI/CSA Z21.50 – 2019 as

vented gas fireplaces.

—

Installation must conform to local codes. Check

local codes prior to installation. In the absence of

local codes, installation must conform with

current National Fuel Gas Code, ANSI Z223.1.

Содержание Isokern MAXIMUS 82L120






































































Результаты поиска

Содержание Isokern MAXIMUS 82L120

Отзывы:

Похожие инструкции для Isokern MAXIMUS 82L120

Бренды по названию

Популярные бренды

EarthCore Isokern MAXIMUS 82L120, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Результаты поиска

Содержание Isokern MAXIMUS 82L120

Отзывы:

Похожие инструкции для Isokern MAXIMUS 82L120

Бренды по названию

Популярные бренды