Spraying - from the Paint Pot
Tip: Before starting your project, practice spraying onto waste cardboard.
1. Fill the Paint Pot (12) with your coating material – and check dilution. DO NOT FILL above the start of the threaded neck.
2. Push the Rigid Pick-Up Tube (11) firmly into the base of the spray gun body. Screw the Paint Pot (12) onto the spray gun body tightly.
3. Set Paint Flow Adjuster (#8, Fig.25) to any desired setting.
4. Uncoil the Air Hose (15) and attach it to the back of the spray gun and the other end to the SprayStation Gemini
®
. Uncoil the power cable and
plug in to the electrical outlet.
5. Turn the turbine on.
6. Fine tune spray output with paint flow adjuster on gun - ¼ to ¾ setting produces the best spray.
7. An airtight seal is essential for the correct operation of this spray gun. Before operating the unit please ensure that the Paint Container Gasket (9) is
>>>
in place and the Paint Pot (12) is securely fixed to the spray gun body.
Tip:
If you are spraying a ceiling angle the Rigid Pick-up Tube (11) to the rear of the paint pot or if you are spraying a floor surface angle the rigid pick-up
tube to the front of the pot. This will ensure you spray as much material as possible before needing to refill the pot.
As some paints, wood preservatives and other sprayable materials contain particles that have differing qualities or you may be using an old paint, we
recommend that you filter your material when filling the paint pot of the spray gun or spraypack, through either a funnel with a filter on it or through
hosiery. This will ensure that no large particles enter the paint pot, so preventing blockages and providing you with trouble-free spraying.
ALWAYS MAKE SURE THAT THE PRODUCT IS ON A STABLE AND LEVEL SURFACE AND FREE FROM DUST AND DEBRIS OR LIQUIDS.
ALWAYS KEEP THE PRODUCT AS FAR AWAY FROM THE SPRAYING AREA AS POSSIBLE TO PREVENT PAINT CONTAMINATING THE MOTOR.
MASK ANY AREA YOU DO NOT WISH TO SPRAY.
13
Cleaning Instructions - Spraying from the Paint Pot
●
Disconnect the Air Hose (15) from the spray gun.
●
Remove the Paint Pot (12).
●
Pour any left over paint into its container so that it can be used in the future. Pull the trigger to allow paint to run out of the Rigid Pick-Up Tube (11).
●
Connect the Air Hose (15) to the spray gun.
●
Pour a quantity of the respective thinners into the Paint Pot (12), reassemble the spray gun, then spray this liquid through the spray gun. Repeat this
until the thinners being sprayed is coming through with no traces of paint.
●
Clean any traces of paint off the outside of the spray gun.
●
Clean the Paint Container Gasket (9).
DVD
DVD
●
Unscrew Air Cap Ring (2).
●
Remove Air Cap (3).
●
Remove Spray Direction Plate (4).
●
Using Needle and Fluid Tip tool - pincer end A (1) remove the Fluid Tip (5).
●
Insert Needle and Fluid Tip end B (1) into the inner tube and unscrew the Needle (7) anticlockwise, then pull to release the Needle.
●
Place all of these items into a container and clean, using a brush and the respective thinners.
Cleaning Instructions - Spray Gun
(Fig.25)
(Priming not required)
1) Uncoil the black air hose from around the bucket and put it to one side.
2) Fit the Rigid Pick-Up Tube (Fig.9) and paint container to the gun (for first time use, the gun already
comes supplied like this).
3) Then fit the black air hose to the head unit and gun using a TWIST motion.
(Water & solvent-based coatings may be used with this set-up)
Small Projects - from the Paint Pot
Содержание SPRAYSTATION GEMINI
