Eagle CUDA 250i S/Map Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 172

background image

158

FCC Compliance

This device complies with Part 15 of the U.S. Federal Communi-
cations Commission (FCC) Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful in-
terference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired opera-
tion.
Changes or modifications not expressly approved by the manu-
facturer could void the user's authority to operate the equip-
ment.

Note:

This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the factory customer service department for help.

«
...
164
165
166
167
168
...
»

Содержание CUDA 250i S/Map













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CUDA 250i S/Map

troller 2.0 combo

Бренд: Marcum Technologies Страницы: 13

Бренд: FishHunter Страницы: 30

LCD Fish/Depth Finder

Бренд: Lilliput Страницы: 23

nuvi 150 series

Бренд: Garmin Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды