Eagle CUDA 250i S/Map Скачать руководство пользователя

Страница: 132 / 172

124

Route Planning command on Main Menu (left). Routes menu (center);

Edit Route menu (right). Navigate Route command is selected.

2. Press

↓

to select

route name

ENT

3. Upon arrival at your destination, cancel navigation:
press

MENU

↓

ANCEL

AVIGATION

ENT

←

to Y

ENT

The following figures show what the Navigation Page and Map Page
look like while navigating a route.

Fig. 1 shows the Navigation Page at the start of a route, heading

straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived
at Wpt 1; the arrival alarm has been triggered and the bearing arrow on

the compass rose has turned to point toward Wpt 2, off to the northeast.

Figure 2.

Figure 1.

Содержание CUDA 250i S/Map












































































































































































Результаты поиска

Содержание CUDA 250i S/Map

Отзывы:

Похожие инструкции для CUDA 250i S/Map

Бренды по названию

Популярные бренды

Eagle CUDA 250i S/Map, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CUDA 250i S/Map

Отзывы:

Похожие инструкции для CUDA 250i S/Map

Бренды по названию

Популярные бренды