background image

KX-III

MANUAL

www.

eaeusa

.us

26

Before Energizing

Energizing

7-

 It is recommended that no energy is applied 

to the line even if the insulation resistance test 

described in page 12 section 2 successfully 

completed.

8-

 When the equipment is energized for the 

first time, qualified electrical personnel must be 

present. If short circuits and earth faults due to 

damage or poor installation practices are not 

detected in the exit procedure, serious damage 

may occur when the power is turned on.

9-

 When the power is supplied, the busway 

must not have an electrical load. Since the 

busway typically runs through several rooms 

and ground level, care must be taken to see 

that all devices supplied by the busway path 

are in the "OFF" position.

10-

 The equipment must be energized in 

sequence starting from the welding end of the 

system and working towards the load side. In 

other words, it energizes the main devices, then 

the feeder devices and then the branch-circuit 

devices. Turn the devices to the "ON" position 

with a solid positive motion.

11-

 Once all overcurrent devices have been 

switched on, loads such as lighting circuits, 

contactors, heaters and motors can be turned 

ON.

12-

 When properly used, the busway will have 

a moderate hum. Excessive noise may be 

an indication of hardware that has not been 

extruded or incorrectly mounted metal parts.

13-

 All busway ratings, routings and supporting 

systems  should  be  checked  as  per  final 

isometric drawings.

14-

 All busway ratings, routings and supporting 

systems  should  be  checked  as  per  final 

isometric drawings.

15-

 All busway system should be checked 

visually to be certain that they are clean 

and secure. Loose and/or contaminated 

connections increase electrical resistance 

which can cause overheating.

 

16-

 Any type of blower or compressed air 

should not be used to avoid blowing dust into 

busway joints, tap off boxes or circuit breakers. 

If there is accumulation of dust and dirt, clean 

it off by using a soft brush, vacuum cleaner, or 

clean lint free rags. 

17-

 All joints should be correctly tightened 

according to the torque value given and should 

be marked. Then install the locking plates 

correctly.

18-

 All Tap Off boxes fed from the busway 

should be on ''OFF'' position.

19-

 The busway runs should be isolated by 

disconnecting all connections to transformers, 

switchboards, meters, etc.

20-

 Insulation resistance test with an insulation 

resistance test equipment rated 1000V AC 

should be conducted to verify the integrity 

of the system.This test should be performed 

between phases, neutral and earth. Permanent 

records should be kept of resistance readings. 

If the insulation reading appears to be lower 

than 1 megaohm, then the cause should be 

investigated.

21-

 The system phase squence should be 

checked in order to match the busway phases 

sequence before reconnecting all connections 

to transformers, switchboards, meters, etc.

Содержание E-LINEKX-III





































Отзывы: