E2S D1xS2FAC230-A страница 10 Скачать руководство пользователя

Страница: 10 / 20

E2S Warning Signals

Impress House, Mansell Road, Acton, London W3 7QH [email protected] e2s.com D190

001

UL Issue B 27/10/2021

FIRE INSTRUCTION & SERVICE MANUAL

D1xS Sounder UL464 / CAN/ULC

S525 Fire

Models: D1xS1

DC024

A. D1xS2

DC024

D1xS1

DC024

S. D1xS2

DC024

•

55°C to +85°C /

67°F to +185°F

•

Units can be mounted using at least 2 of the 3

off ø7mm holes in the mounting bracket.

•

D1xS1RDC024

A & D1xS1RDC024

S are approved for use as an audible signal appliance for fire alarm use –

Public Mode (UL464 &

CAN/ULC

S525) and produce a minimum sound pressure level of US: 81.62dB(A); CA: 84.8dB(A) at 10 feet, (figures @ worst case

11.5Vdc).

•

D1xS1RDC024

A & D1xS1RDC024

S produce a minimum sound pressure level of US: 83.4dB(A); CA: 86.4dB(A) at 10 feet (@24Vdc)

•

D1xS1FDC024

A & D1xS1FDC024

S are approved for use as an audible signal appliance for fire alarm use –

Public Mode (UL464 &

CAN/ULC

S525) and produce a minimum sound pressure level of: US: 92.06dB(A); CA: 98.2dB(A) at 10 feet, (figures @ worst case

11.5Vdc).

•

D1xS1FDC024

A & D1xS1FDC024

S produce a minimum sound pressure level of: US: 94.62dB(A); CA: 100.9dB(A) at 10 feet

(@24Vdc)

•

D1xS2FDC024

A & D1xS1FDC024

S are approved for use as an audible signal appliance for fire alarm use –

Public Mode (UL464 &

CAN/ULC

S525) and produce a minimum sound pressure level of P1: US: 93.56dB(A) / P2: US: 94.9dB(A); CA: 101.6dB(A) / P3: US:

95.51dB(A); CA: 101.8dB(A) at 10 feet, (figures @ worst case 11.5Vdc).

•

D1xS2FDC024

A & D1xS2FDC024

S produce a minimum sound pressure level of P1: US: 95.64dB(A) / P2: US: 98.42dB(A); CA:

105.2dB(A) / P3: US: 102.7dB(A); CA: 109.4dB(A) at 10 feet (@24Vdc)

•

D1xS2HDC024

A & D1xS2HDC024

S are approved for use as an audible signal appliance for fire alarm use –

Public Mode (UL464 &

CAN/ULC

S525) and produce a minimum sound pressure level of P2: US: 95.51dB(A); CA: 103.8dB(A) / P3: US: 96.24dB(A); CA:

105dB(A) at 10 feet, (figures @ worst case 11.5Vdc).

•

D1xS2HDC024

A & D1xS2HDC024

S produce a minimum sound pressure level of P2: US: 100.2dB(A); CA: 108.5dB(A) / P3: US:

103.5dB(A); CA: 111.6dB(A) at 10 feet (@24Vdc)

•

For Fire Alarm applications, the Sounder Volume must be at the highest setting, (see volume control section). For fire alarm use, Tone

12 as shown below must be selected:

•

Connection Terminals: Pluggable

AC: 1.0

2.5mm

/ AWG18

AWG12

DC: 0.2

2.5mm

/ AWG24

AWG12

•

Terminal Tightening torque 0.4Nm

•

To maintain Ingress Protection, cable entries must be fitted with suitably rated cable glands or stopping plugs

•

Units can be located indoor or outdoor wet use, wall or ceiling mounted and there are no limitations on orientation

•

Factory finishes are not intended to be modified

Attention: Installation must be carried out by an electrician in compliance with the National Electrical Code, NFPA 70, and the National Fire Alarm
Signaling Code, NFPA 72 or CSA 22.1 Canadian Electrical Code, Part I, Safety Standard for Electrical Installations, Section 32. / L'installation doit
exclusivement être réalisée par du personnel qualifié, conformément au code national d'électricité américain, NFPA 70, et le code national d

’

alarrme

incendie et de signalisation NFPA 72 ou CSA 22.1 Code canadien de l'électricité, première partie, norme de sécurité relative aux installations électriques,
Section 32

Attention: Disconnect from power source before installation or service to prevent electric shock / Débranchez

le de la source d'alimentation avant l'instal-

lation ou l'entretien pour éviter tout choc électrique.

Attention: Do not paint / Ne pas Peinturer

1000Hz(0.5s on, 0.5s off)x3 + 1s gap ISO 8201 Temporal
Pattern

Stage 1
Set DIP
SW 1
Tone No.

Tone Description

Tone Visual

Stage 1 & 2
DIP SW 1/2

Settings

1 2 3 4 5 6

Stage 3
Set DIP