E2S BExCTS110-05 Скачать руководство пользователя страница 3

_______________________________________________________________________________________________________________________________ 

European Safety Systems Ltd.

   Impress House, Mansell Road, Acton, London W3 7QH           sales@e-2-s.com              Tel: +44 (0)208 743 8880 

                                                                                                                                                             www.e-2-s.com             Fax: +44 (0)208 740 4200 
Document No. D210-00-681-IS           Issue 3          20-04-2020                         Sheet 3 of 8                                                                                            

 

M20 entries and labels on the same side). Carefully push the 
cover  in  place  allowing  time  for  the  air  to  be  expelled.  Only 
after  the  cover  is  fully  in  place  should  the  four  M6  Stainless 
Steel  A4-80  cover  bolts  and  their  spring  washer  be  inserted 
and  tightened  down.  If  the  cover  jams  while  it  is  being 
inserted,  carefully  remove  it  and  try  again.  Never  use  the 
cover bolts to force the cover into position. 

 

8)  Power Supply Selection 

 

It is important that a suitable power supply is used to run the 
equipment.  The  power  supply  selected  must  have  the 
necessary  capacity  to  provide  the  input  current  to  all  of  the 
units. 

 

The  following  table  shows  the  input  current  taken  by  the 
various combined sounder beacons and shows the maximum 
voltage  at  which  the  combined  sounder  beacons  can  be 
operated: 

 

Sounder Section 

The input current to the sounder section will vary according to 
the voltage input level and the frequency of the tone selected. 
The  current  levels  shown  above  are  for  the  440Hz 
Continuous tone @ nominal input voltage. 

 

Beacon Section 
The input current to the beacon section will vary according to 
the  voltage  input  level.  The  current  levels  shown  above  are 
for nominal input voltage.  

 

9)  Selection of Cable. Cable Glands, Blanking 

Elements & Adapters

 

 

When  selecting  the  cable  size,  consideration  must  be  given 
to  the  input  current  that  each  unit  draws  (see  table  above), 
the number of combined sounder beacons on the line and the 
length  of  the  cable  runs.  The  cable  size  selected  must  have 
the  necessary  capacity  to  provide  the  input  current  to  all  of 
the combined sounder beacons connected to the line.  

 

For  ambient  temperatures,  over  +40ºC  the  cable  entry 
temperature  may  exceed  +70ºC  and  therefore  suitable  heat 
resisting cables and cable glands must be used, with a rated 
service temperature of at least 110ºC 

 

The dual cable gland entries have an M20 x 1.5 entry thread. 
To  maintain  the  ingress  protection  rating  and  mode  of 
protection, the cable entries must be fitted with suitably rated 
ATEX  /  IECEx  certified  cable  glands  and/or  suitably  rated 
ATEX  /  IECEx  certified  blanking  devices  during  installation 
according to EN / IEC60079-14. 
If  a  high  IP  (Ingress  Protection)  rating  is  required,  then  a 
suitable sealing washer must be fitted under the cable glands 
or blanking plugs.  

 

For  use  in  explosive  dust  atmospheres,  a  minimum  ingress 
protection rating of IP6X must be maintained. 
The  BEx  combined  sounder  beacon  range  can  be  supplied 
with the following types of adapters: 

 

M20 to ½” NPT 
M20 to ¾” NPT 
M20 to M25 

 

It  is  important  to  note  that  stopping  plugs  cannot  be  fitted 
onto adapters, only directly onto the M20 entries. 

 

Any  other  adapters  used  must  be  suitably  rated and  ATEX  / 
IECEx certified adapters. 

 

10) Earthing 

 

Both  AC  and  DC  combined  sounder  beacon  units  must  be 
connected  to  an  earth.  The  units  are  provided  with  internal 
and  external  earth  terminals  which  are  both  located  on  the 
terminal chamber section of the unit. 

 

Fig. 3 Internal View of Cover 

 

When  using  the  internal  earth  terminal  ensure  that  the 
stainless steel M4 flat washer is between the incoming earth 
wire and the enclosure.  

 

Internal earthing connections should be made to the Internal 
Earth  terminal  in  the  base  of  the  housing  using  a  ring  crimp 
terminal to secure the earth conductor under the earth clamp. 
The  earth  conductor  should  be  at  least  equal  in  size  and 
rating to the incoming power conductors. 

 

External  earthing  connections  should  be  made  to  the  M5 
earth  stud,  using  a  ring  crimp  terminal  to  secure  the  earth 
conductor  to  the  earth  stud.  The  external  earth  conductor 
should be at least 4mm² in size. 

 

11) Cable Connections 

 

The  combined  sounder  beacon  unit  BExCTS110-05D  has 
separate  printed  circuit  boards  in  the  sounder  and  beacon 
sections.  The  terminals  for  the  incoming  power  supply  and 
telephone  signal  are  on  the  printed  circuit  board  in  the 
sounder section and the terminals for the beacon are on the 
printed  circuit  board  in  the  beacon  section  (see  figures  5a, 
5b, 7a and 7b). See section 7 of this manual for access to the 
enclosure.  See  section  12  and  13  for  AC  and  DC  wiring 
diagrams respectively.  
 
Wires  having  a  cross  sectional  area  between  0.5  mm²  to 
2.5mm²  can  be  connected  to  each  terminal  way.  If  an  input 
and  output  wire  is  required,  the  2-off  Live/Neutral  or  +/- 
terminals  can  be  used.  If  fitting  2-off  wires  to  one  terminal 

Model No. 

Nominal 

I/P 

Voltage 

Sounder 

Current 

Beacon 
Current 

Max. 

I/P 

Volts 

BExCTS110-05D-P 
DC012 

12Vdc 

195mA 

750mA 

14V 

BExCTS110-05D-P 
DC024 

24Vdc 

265mA 

300mA 

28V 

BExCTS110-05D-P 
DC048 

48Vdc 

130mA 

180mA 

54V 

BExCTS110-05D-P 
DC115 

115Vac 

110mA  

140mA 

126V  

BExCTS110-05D-P 
AC230 

230Vac 

56mA 

55mA 

253V 

Internal 
Earthing 

Internal 
Bonding 
Wire 
Terminal 

2-off M20 
Cable 
Entries 

Содержание BExCTS110-05









Отзывы: