E.T. Systems Drive 300 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

E.T. Systems Drive 300 Скачать руководство пользователя страница 17

17

Using the control card display and dashboard.

The Drive 300 is equipped with an LED display and interactive keys for simplified programming and diagnostics. All setup of the various features requires

that the control card dashboard be used. Below are the functions of each key on the dashboard.

rdy

Enter programming, advance to next

level of option on display or save value

on display.

Exit menu levels without saving.

Navigate backward in menus, decrease

values or indicate lefthand closing gate

in runtime setup function.

Navigate forward in menus, increase

values or indicate righthand closing

gate in runtime setup function. Test

BT mode setting from “ready” status.

Before continuing with the commisioning.

If you are unfamiliar with the functionality of this product’s modes, it is suggested that you

familiarise yourself with the basic and advanced operating features detailed from page 32

of this instruction manual.

«
...
15
16
17
18
19
...
»

Содержание Drive 300



















































Отзывы:

Нет отзывов