manualshive.com logo in svg

E.T. Systems Drive 300, Инструкции по установке, Страница: 11 / 50

Поделиться
Скачать
E.T. Systems Drive 300 Скачать руководство пользователя страница 11

11

Mounting the operator onto the baseplate.

Removing the cover:

The cover is secured in place by means of four screws. One of which is secured beneath the manual override lever. 

Using a Philips ® screwdriver remove the 

four cover screws.

Unlock and lift the manual override.

Lift the main cover to remove it.

Mounting the gearbox:

 (You will need a 13mm socket or spanner)

The gearbox is fastened onto the baseplate by means of the 2 x 25mm x M8 machine bolts and custom mounting plates. The gearbox distance from 

the gate can be adjusted backwards and forwards by up to 30mm. Remember to ensure that there is enough space allowed between the fascia of the 

pinion and the proudest part of the gate that passes the pinion. This is to prevent any part of the gate snagging on the pinion as the gate runs.

At this stage of the installation it is recomended that you place 2 x 2mm thick flat bars in between the baseplate and motor to facilitate the correct 

rack height later.  See page 12 and 13 overleaf.

2mm flat bar spacer

8 to 10mm tolerance

Pinion

Side view

1

2

3

Diagram 

number

Description

1

M8 Machine bolt.

2

M8 Flat washer.

3

Mounting plate.

Содержание Drive 300



















































Отзывы:

Нет отзывов