E-line ELI-SIP2-NVR8 Скачать руководство пользователя

Страница: 97 / 231

185



IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two IP address

format and you can access via them.



MAC address: The host in the LAN can get a unique MAC address. It is for you to access in the LAN. It is

read-only.



IP address: Here you can use up/down button (



) or input the corresponding number to input IP

address. Then you can set the corresponding subnet mask the default gateway.



Default gateway: Here you can input the default gateway. Please note system needs to ch eck the

validity of all IPv6 addresses. The IP address and the default gateway shall be in the same IP

section. That is to say, the specified length of the subnet prefix shall have the same string.



DHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet mask

/Gateway. These values are from DHCP function. If you have not enabled DHCP function, IP/Subnet

mask/Gateway display as zero. You need to disable DHCP function to view current IP information.

Besides, when PPPoE is operating, you can not modify IP/Subnet mask /Gateway.



MTU: It is to set MTU value of the network adapter. The value ranges from 1280 -7200 bytes. The

default setup is 1500 bytes. Please note MTU modification may result in network adapter reboot and

network becomes off. That is to say, MTU modification can affect current network service. System

may pop up dialog box for you to confirm setup when you want to change MTU setup. Click OK

button to confirm current reboot, or you can click Cancel button to terminate c urrent modification.

Before the modification, you can check the MTU of the gateway; the MTU of the NVR shall be the

same as or is lower than the MTU of the gateway. In this way, you can reduce packets and enhance

network transmission efficiency.

The following MTU value is for reference only.



1500: Ethernet information packet max value and it is also the default value. It is the typical

setup when there is no PPPoE or VPN. It is the default setup of some router, switch or the

network adapter.



1492: Recommend value for PPPoE.



1468: Recommend value for DHCP.



Preferred DNS server: DNS server IP address.



Alternate DNS server: DNS server alternate address.



Transfer mode: Here you can select the priority between fluency/video qualities.



LAN download: System can process the downloaded data first if you enable this function. The

download speed is 1.5X or 2.0X of the normal speed.



LAN download: System can process the downloaded data first if you enable this function. The

download speed is 1.5X or 2.0X of the normal speed.

After completing all the setups please click save button, system goes back to the previous menu.

Содержание ELI-SIP2-NVR8








































































































































































































































Результаты поиска

Содержание ELI-SIP2-NVR8

Отзывы:

Похожие инструкции для ELI-SIP2-NVR8

Бренды по названию

Популярные бренды

E-line ELI-SIP2-NVR8, Руководство пользователя

Результаты поиска

Содержание ELI-SIP2-NVR8

Отзывы:

Похожие инструкции для ELI-SIP2-NVR8

Бренды по названию

Популярные бренды